Search found 15 matches

by ssharkey
Wed Apr 29, 2009 8:41 pm
Forum: General software support
Topic: Can't find download link for the latest analysis software
Replies: 2
Views: 7585

http://www.race-technology.com/upload/products/software/setup_7011.exe Cheers.... Looks like I should find another 0.85s on the same car/setup - assuming the same conditions.... Now if the higher compression and cam will give me another second and slicks a couple more I'll be just 2.5 seconds off a...
by ssharkey
Fri Apr 24, 2009 9:53 pm
Forum: General software support
Topic: Can't find download link for the latest analysis software
Replies: 2
Views: 7585

Can't find download link for the latest analysis software

I've been to the page linked in the site (http://www.race-technology.com/download ... _7453.html) but I can't see where to click to get a download...
by ssharkey
Tue Apr 22, 2008 2:17 pm
Forum: General software support
Topic: More on graphs
Replies: 5
Views: 10160

The min, max, ave are single values. I see you are aware of some of the strange logic in your question from your multiple RPMs note. An obvious if somewhat fabricated example is to have rpm on the x-axis and for each rpm plotting the highest torque or horsepower value. Perhaps this is better suited...
by ssharkey
Mon Oct 08, 2007 9:52 pm
Forum: General software support
Topic: Can I display fuel used / fuel remaining on DL1 + DASH 1?
Replies: 2
Views: 7393

The DASH 1 is very unsophisticated in what it displays - there is (as far as I have found) no way to do this. It can't even display sensible bar graphs for anything other than the lat & long G forces.

Steve
by ssharkey
Tue Sep 25, 2007 10:27 pm
Forum: General support questions
Topic: V7 Beta - Public
Replies: 30
Views: 48553

Well I've been using the public beta now but why has it suddenly caused all my rpm output to look very stepped? I'm guessing there is a setting that I need to reset. I'm also a little bit miffed that I have had to set up all my variables again from scratch.
by ssharkey
Tue Sep 25, 2007 10:25 pm
Forum: General software support
Topic: Comparing acceleration runs
Replies: 7
Views: 12978

Check out Results -> Performance Calculations. It's a table based method, not graphical. Has anyone found the performance table at all satisfactory? I'm guessing that to actually get it to make sense you have to drive for the table - whenever I take a look at this table the performance of the car A...
by ssharkey
Mon Aug 20, 2007 5:02 pm
Forum: General support questions
Topic: Lap counter on Dash 1
Replies: 2
Views: 6808

Currently not possible on the DASH1 (DASH2 does have it). Only the RT guys can comment if it's something that could be added by a firmware update down the road. I'm sure it could be added - whether it will be is another matter entirely. When I questioned the price difference between DASH1 & DAS...
by ssharkey
Fri Aug 17, 2007 1:53 pm
Forum: General software support
Topic: More on graphs
Replies: 5
Views: 10160

More on graphs

Reposted from possibly the wrong place - though these might turn out to be for the Requested features list but thought I ought to check they can't be achieved already. 1. Min/Max/Avg values I would like to be able to plot the maximum, minimum or average of one variable against another. By way of exa...
by ssharkey
Fri Aug 17, 2007 10:43 am
Forum: General support questions
Topic: Graphs
Replies: 0
Views: 15595

Graphs

I would like to be able to plot the maximum, minimum or average of one variable against another. By way of example - Against rpm plot the maximum torque - obviously you can hve multiple readings for the given rpm value. I'm sure there must be a way of doing this but can't find it. Steve Sharkey
by ssharkey
Thu Aug 16, 2007 2:14 pm
Forum: General support questions
Topic: DASH1 & DL1
Replies: 5
Views: 8978

2. Hmmm. Could be a dodgy CF card? I hope not it's only 2 months old. If you save your screen layout it remembers the variables. I, for example, have a tab called "Real Time" which shows a trackmap, sector times, dashboard and playback controls. Works (although a bit buggy in the V7 beta ...
by ssharkey
Thu Aug 16, 2007 1:42 pm
Forum: General support questions
Topic: DASH1 & DL1
Replies: 5
Views: 8978

DASH1 & DL1

Okay the DL1 has had the Hardware Mod. it's all installed now BUT there are more questions than ever now... 1. I just took the car out for a run. The DL1 now seems to start logging as soon as I switch it on. Never used to do this... I will create a new SETUPBIN file. The Run manager says the log was...
by ssharkey
Fri Aug 03, 2007 4:15 pm
Forum: General support questions
Topic: DASH 1 - No display
Replies: 6
Views: 9888

1. Re your DL1 - there are relatively few DL1s that require this mod, only the very early ones, it's easy to forget about this caveat. I have one myself, and yet I completely failed to recognize the issue the first (and only, I think) time I sold a DASH1 to an early DL1 customer and it didn't work....
by ssharkey
Fri Aug 03, 2007 10:12 am
Forum: General support questions
Topic: DASH 1 - No display
Replies: 6
Views: 9888

In my experience, it does not appear to me that RT knows which serial number unit belongs to which specific customer From a company that specialises in data capture & logging that's a pretty poor record. But my point was that when I placed the order EVEN if they didn't know which unit I had the...
by ssharkey
Fri Aug 03, 2007 9:39 am
Forum: General support questions
Topic: DASH 1 - No display
Replies: 6
Views: 9888

Opinions invited... What should I do? I get absolutely no response from RT UK where I bought the DASH1 & (originally) the DL1 - in fact I had to ring them and they said the response I got from RTUSA can be treated as their official response. I am grateful that our US cousins still know something...
by ssharkey
Wed Aug 01, 2007 11:54 pm
Forum: General support questions
Topic: DASH 1 - No display
Replies: 6
Views: 9888

DASH 1 - No display

Okay I am just about ready to start shouting now - I bought a DASH 1 last week to go with my DL1 (bought some time ago). The new unit eventually arrived earlier this week but I am unable to use it because the instructions say if not bought with a Logger you will need to reflash the logger. Fair enou...

Go to advanced search