Search found 33 matches
- Sat Aug 16, 2008 8:09 pm
- Forum: General support questions
- Topic: Extending the Dash1 cable
- Replies: 6
- Views: 12230
- Fri Jun 27, 2008 6:40 pm
- Forum: General support questions
- Topic: RPM Filtering for Dash II
- Replies: 4
- Views: 8911
- Sat Jun 07, 2008 7:58 pm
- Forum: Installation questions
- Topic: DL1 and Dash 2 starting log
- Replies: 4
- Views: 9467
Current Version from software is 7-2 serial.618 whats latest version numbers please need the New est Hex file for my DL1 please my dash2 wont start stop logging when connected to the DL1 if i start logging then power up the Dash everything is fine. i belive martin said i need the latest Version of t...
- Wed May 28, 2008 8:39 pm
- Forum: Sensor-related questions
- Topic: Funky RPM Readnigs
- Replies: 9
- Views: 15036
yup been here got the badge. was told the -coil feed had interferance and i should try to get a better signal went down the line of fitting a Gear tooth sensor to a bracket and located this in front of the crank and then spent a week trying to work out how to display the information i was getting cu...
- Wed May 28, 2008 8:27 pm
- Forum: Installation questions
- Topic: Mounting holes on Dash2 - really M4?
- Replies: 8
- Views: 16260
they are thread m4 but the anodising has made the holes a little tight using some self tapping machined m4 screws ( made for Trend Controls ) to self tap int m4 holes with no thread the holes stood up well to being re-tapped in this way due to the short depth the problem is you carnt Tap the holes w...
- Thu May 22, 2008 11:36 am
- Forum: General support questions
- Topic: No RUN data recorded
- Replies: 66
- Views: 81281
- Thu May 22, 2008 11:31 am
- Forum: General support questions
- Topic: Simple Telemetry?
- Replies: 4
- Views: 8483
- Tue May 20, 2008 10:23 pm
- Forum: General support questions
- Topic: No RUN data recorded
- Replies: 66
- Views: 81281
- Thu May 15, 2008 11:40 pm
- Forum: General support questions
- Topic: Simple Telemetry?
- Replies: 4
- Views: 8483
hi Guys i perchased on ebay from hong kong Wirless Serial cards on 915mhz these cards are limited to 19k2 transmission but i configured the DL1 down to 19k2 and hey presto i have wirless Telemetry they use 5V so conecting to the ref [5v] on the DL1 was easy and 5v is found on a laptop on the USB por...
- Thu May 15, 2008 11:24 pm
- Forum: Sensor-related questions
- Topic: Autometer sensors
- Replies: 7
- Views: 15049
just my opinion but if al the sensors are Voltage output sensors you need a 0-Degrees setup . or referance temperature you take the sender put it at a know fixed temperature 0 degrees is simpe cold water filled with ice leave for 5 mis the water is pretty well 0 degress as the ice melts the voltage ...
- Thu May 15, 2008 11:17 pm
- Forum: Sensor-related questions
- Topic: Wiring help needed for temperature sensor
- Replies: 3
- Views: 9136
the RT sensors are set in the analisys software as external sensors and the data froma DL1 takes the Raw voltage reading the software converts to DegC on th eother hand if you configure a Dash 1-2 they show the actual Temperatures A1 is analog1 [5v] simply selsect from a drop down menu Bosch air tem...
- Wed May 14, 2008 7:56 pm
- Forum: General software support
- Topic: finding HP
- Replies: 6
- Views: 11589
- Tue May 13, 2008 6:33 pm
- Forum: General software support
- Topic: finding HP
- Replies: 6
- Views: 11589
- Wed Apr 30, 2008 11:06 pm
- Forum: Installation questions
- Topic: DL1 and Dash 2 starting log
- Replies: 4
- Views: 9467
- Mon Apr 28, 2008 7:10 pm
- Forum: Installation questions
- Topic: Tapping into existing wiring
- Replies: 7
- Views: 18248
to get heatshrink over a cable assumes that you can get to both ends cleanly to slide it over Lol your going to CUT it you have acces to both ends. anyways you didnt say you didnt want the instaltion Perminent Perminent is Propper use Botch locks then and make it look really rough was only my opini...