Search found 79 matches
- Wed Aug 14, 2013 2:46 pm
- Forum: General software support
- Topic: a count variable
- Replies: 8
- Views: 15446
- Wed Aug 14, 2013 12:42 pm
- Forum: General software support
- Topic: a count variable
- Replies: 8
- Views: 15446
- Wed Aug 14, 2013 12:13 pm
- Forum: General software support
- Topic: a count variable
- Replies: 8
- Views: 15446
- Tue Aug 13, 2013 5:00 pm
- Forum: General software support
- Topic: a count variable
- Replies: 8
- Views: 15446
- Mon Aug 12, 2013 5:17 pm
- Forum: General software support
- Topic: a count variable
- Replies: 8
- Views: 15446
a count variable
Hello, Is there any way to set up a count variable in analysis? I’m using a torque load cell to measure the breaking force of something... torque is the most important reading i want, but there is also an output for number of degrees of rotation. It is basically just an on/off switch that cycles e...
- Wed May 29, 2013 12:19 pm
- Forum: Sensor-related questions
- Topic: DL1 wont read bridge amp
- Replies: 6
- Views: 18955
- Wed May 22, 2013 4:52 pm
- Forum: Sensor-related questions
- Topic: DL1 wont read bridge amp
- Replies: 6
- Views: 18955
Are you getting 0v on the DL1 or are you seeing nothing at all? Make sure that the unit is configured to be logging the data and/or transmitting it on the serial port if you are monitoring it on a PC. Martin currently trying to just log onto card, and check in analysis, i checked that serial is on,...
- Wed May 22, 2013 4:23 pm
- Forum: Sensor-related questions
- Topic: DL1 wont read bridge amp
- Replies: 6
- Views: 18955
the range of the load cell is 500lbs @ +/-10vdc. when i stand on the load cell mulit meter it is saying 4.985vdc.. (im around 250lbs, stands to reason) i connect DL1 in parallel to meter, meter reads same, log data, load into analysis, analaysis shows 0 to .05mV , assume it should show same as meter...
- Tue May 21, 2013 7:18 pm
- Forum: Sensor-related questions
- Topic: DL1 wont read bridge amp
- Replies: 6
- Views: 18955
DL1 wont read bridge amp
trying to set up a brake pedal load sensor PCB# 1203-01A, with the PCB# 8162 bridge amp. The load cell works fine on the bench with a 12vdc supply, and reading the output with a mulitmeter. ie squeeze the load cell, the volts goes up on the multimeter... easy. I plug it into an analoge CH of a DL1, ...
- Thu Apr 04, 2013 12:20 pm
- Forum: General support questions
- Topic: bad analgoue readings
- Replies: 7
- Views: 13838
- Wed Apr 03, 2013 8:33 pm
- Forum: General support questions
- Topic: bad analgoue readings
- Replies: 7
- Views: 13838
- Wed Apr 03, 2013 5:26 pm
- Forum: General support questions
- Topic: RT USA?
- Replies: 1
- Views: 7634
RT USA?
is RT USA ok? ive sent Al 3 emails and 2 voice mails over the past 5 days...
nothing
nothing
- Wed Apr 03, 2013 2:04 pm
- Forum: General support questions
- Topic: bad analgoue readings
- Replies: 7
- Views: 13838
- Wed Apr 03, 2013 1:42 pm
- Forum: General support questions
- Topic: bad analgoue readings
- Replies: 7
- Views: 13838
bad analgoue readings
i was experienceing some problems using the analogue channels in our DL1. this is just a simple 5 -12vdc signal applied on... off, on, off, on, off applied to each of the 8 ananloge channels. this data should not look like this. reflash, new config in DL1 analysis reset to factor defaults no filteri...
- Mon Aug 06, 2012 3:30 pm
- Forum: General support questions
- Topic: DASH4 Pro, show text on value
- Replies: 4
- Views: 8342