Search found 19 matches

by rbahr
Mon Aug 20, 2018 5:27 pm
Forum: General support questions
Topic: Looking for Firmware updates
Replies: 3
Views: 19799

Re: Looking for Firmware updates

Hi All,

Still trying to find the latest firmware files for the boxes listed above. I have found them in the past on the site, but they now seem to be gone...

Any help would be appreciated

Thanks

Ray
by rbahr
Sun Aug 19, 2018 3:56 am
Forum: General support questions
Topic: Looking for Firmware updates
Replies: 3
Views: 19799

Looking for Firmware updates

For Video4, Dash4Pro, and dl1.

Where can I find these?

Thanks

Ray
by rbahr
Wed Aug 02, 2017 6:25 pm
Forum: General software support
Topic: Problem with Lap and Sector markers
Replies: 3
Views: 14077

Re: Problem with Lap and Sector markers

Ok, If I deselect that, I should be able to manually enter what I want?
by rbahr
Wed Aug 02, 2017 4:43 pm
Forum: General software support
Topic: Problem with Lap and Sector markers
Replies: 3
Views: 14077

Problem with Lap and Sector markers

Hi All, I load up a .run file and the Analysis tool loads it, automatically creates a lap marker and then a large number of sector markers. These are numbered something like M2, M2.1, M2.2, M3,... and there seem to be many. In addition, I do not see a reasonable number of sector columns I would have...
by rbahr
Wed Aug 02, 2017 4:42 pm
Forum: General support questions
Topic: Dumb Lap marker / sector question
Replies: 1
Views: 4050

Dumb Lap marker / sector question

Hi All, I load up a .run file and the Analysis tool loads it, automatically creates a lap marker and then a large number of sector markers. These are numbered something like M2, M2.1, M2.2, M3,... and there seem to be many. In addition, I do not see a reasonable number of sector columns I would have...
by rbahr
Mon May 29, 2017 4:10 pm
Forum: General software support
Topic: Video4 rear connectors
Replies: 2
Views: 7780

Re: Video4 rear connectors

Perfect!

Thanks

Ray
by rbahr
Mon May 29, 2017 3:45 am
Forum: General software support
Topic: Video4 rear connectors
Replies: 2
Views: 7780

Video4 rear connectors

Hi All,

Where can I get the connectors for the video4 unit?

Thanks

Ray
by rbahr
Tue Jun 18, 2013 12:17 pm
Forum: Sensor-related questions
Topic: Which ( Bosch ??) Oil preassure sensor is the Dash II/DL1
Replies: 2
Views: 6800

Thanks

Ray
by rbahr
Thu May 09, 2013 1:45 pm
Forum: General software support
Topic: Help - Dash2 works and then feezes
Replies: 6
Views: 12915

Perhaps 'bad' was not the best choice of words. Having designed fairly complex communication systems for the last 30+ years, I make some assumptions, no flow control and simple ring architectures make for systems that are less tolerant to faults and there are better easy ways. Also I am more than wi...
by rbahr
Wed May 08, 2013 8:13 pm
Forum: General software support
Topic: Help - Dash2 works and then feezes
Replies: 6
Views: 12915

Thanks!

Why is this interface so badly designed? It is not at all difficult to avoid a lot of these problems...

Ray
by rbahr
Wed May 08, 2013 1:54 am
Forum: General software support
Topic: Help - Dash2 works and then feezes
Replies: 6
Views: 12915

I think I found it. I found a ground loop and wired in a good solid ground, I also removed the Dash2 config file from the DL1///

Thanks

Ray
by rbahr
Sun May 05, 2013 5:54 pm
Forum: General software support
Topic: Help - Dash2 works and then feezes
Replies: 6
Views: 12915

Help - Dash2 works and then feezes

Hope to be at the track tomorrow... I have a dash2 connected to a DL1. After the car is on for ~ 5 min the Das2 display freezes with whatever is being displayed - 1st question - can the RS232 connection cause this is I have mucked things up? Is there supposed to be a crossover between the Dash2 and ...
by rbahr
Wed Mar 27, 2013 5:12 pm
Forum: General support questions
Topic: Problem with DL1 MK2
Replies: 2
Views: 5167

If you mean a null modem - reverse rx & tx -I don't think so. I am using the same cable I used to reflash the DASH2. Should I be?

TIA

Ray
by rbahr
Wed Mar 27, 2013 1:15 pm
Forum: General support questions
Topic: Problem with DL1 MK2
Replies: 2
Views: 5167

Problem with DL1 MK2

Hi, Trying to get my DL1 updated firmware wise and cannot get the computer to recognize it. The serial port works as I got my Dash2 configured with the same port/power supply. None of the DL1 support tools seem able to connect to the unit. Is there a return/repair policy (in the US)? Thanks Ray

Go to advanced search