Occassionally the Dash2 seem to recieve a new marker at startup despite the compact flash card is formatted and empty.
Going out on a new track, it is bad news, as last time a marker was added was 300km away.
Why does this happen and how can it be erased?
Thanks for your support
Search found 10 matches
- Tue Apr 28, 2009 3:45 pm
- Forum: General support questions
- Topic: Dash2 displays New Marker with formatted compact flash
- Replies: 6
- Views: 10398
- Tue Apr 28, 2009 4:36 am
- Forum: General support questions
- Topic: DL1 Speed is influenced by RPM
- Replies: 6
- Views: 8177
-The DL1 is mounted with welcro on the floor of the kart, between the front axle and the petrol tank. The antenna is mounted on the top of the spoiler covering the steering column. I still have an old unit, it started behaving funny, making twitch/jump a couple of meters mid cornering, or just freak...
- Mon Apr 27, 2009 10:19 pm
- Forum: General support questions
- Topic: Dash2 peak-hold function
- Replies: 2
- Views: 5017
The thermocouple is connected with an amplifier, so the signal is ok, How do I program the buttons to do a Min/Max view? Normal cart tracks gives the highest exhaust temperature at the end of the straights, and normally you glance at the dash after exit of the following curve which is just a few sec...
- Mon Apr 27, 2009 10:09 pm
- Forum: General support questions
- Topic: DL1 Speed is influenced by RPM
- Replies: 6
- Views: 8177
-Ok, the gps antenna might pick up the RPM then. -The RPM cable is shielded, it lacks a some cm, guess I will have to fix that. it is grounded. -I will revisit the RPM guide, read it last season.. -My two-stroke cart engine lacks injector and cam, but hall-effect to the crank is possible. If I cant ...
- Mon Apr 27, 2009 9:38 pm
- Forum: General support questions
- Topic: DL1/Dash2 Does not start logging
- Replies: 10
- Views: 22236
Update: Compact flash replaced
I tested a different Compact flash card and the logging started with no hassle..
Is it likely that the compact flash card can be corrupted somehow?
By what? Can it be "repaired" by some low-level format or such?
what would cause a failure?
Is it likely that the compact flash card can be corrupted somehow?
By what? Can it be "repaired" by some low-level format or such?
what would cause a failure?
- Mon Apr 27, 2009 3:09 pm
- Forum: General support questions
- Topic: Dash2 peak-hold function
- Replies: 2
- Views: 5017
Dash2 peak-hold function
We use a exhaust gas temperature sensor to tune our 2-stroke cart engine, is there any way to get a peak hold on the dash2, for example the value is always the highest that has occured over the last 5 or 10 seconds. As it is now, the only help is the alarm function as the read-out on the display doe...
- Mon Apr 27, 2009 3:01 pm
- Forum: General support questions
- Topic: Dash2 backlight is turned off
- Replies: 1
- Views: 4243
Dash2 backlight is turned off
When using the Dash2 the backligt is turned off, and stays off, is the backlight low-voltage restricted, if so does anyone the limit?
No toggle or setting seem to be available, is there any?
Any other influences on the backlight function?
No toggle or setting seem to be available, is there any?
Any other influences on the backlight function?
- Mon Apr 27, 2009 2:59 pm
- Forum: General support questions
- Topic: DL1 Runfile on Compact flash corrupted by RPM signal
- Replies: 1
- Views: 3770
DL1 Runfile on Compact flash corrupted by RPM signal
While trying out the RPM connection the Run files on the Compact flash card became unreadable, locked by other application or corrupt, shortening the pickup cable on the helped, also changing to resistor spark plug The installation consists of the RT rpm pickup cable connected to a custom wire harne...
- Mon Apr 27, 2009 2:40 pm
- Forum: General support questions
- Topic: DL1 Speed is influenced by RPM
- Replies: 6
- Views: 8177
DL1 Speed is influenced by RPM
While testing the RPM (high level) it was noted that while standing still and applying throttle the speed recorded increased 1-2 km/h this dispite the vehicle standing still. Disconnecting the RPM pickup caused the problem to go away, but since RPM is needed in the Dash it is not a good solution Has...
- Mon Apr 27, 2009 12:18 pm
- Forum: General support questions
- Topic: DL1/Dash2 Does not start logging
- Replies: 10
- Views: 22236
DL1/Dash2 Does not start logging
This weekend race, when I used Start logging from the Dash2 the following symptoms occured -The 01010110 symbol which indicates connection btw DL1/Dash2 disappeared -No Tick icon showed up -The first shift light diod did not light. The card was recently formatted, wires seemed ok. What may be the re...