cheers Max.
my questions more about the equation - i will give the hardware a shot myself.
Im hoping that those that are more experienced than I will be able to shed some light on turning Hz into BPM. Im thinking it is Hz*60
Search found 12 matches
- Mon Oct 11, 2010 5:38 pm
- Forum: Sensor-related questions
- Topic: heart rate sensor
- Replies: 19
- Views: 109020
- Mon Oct 11, 2010 5:07 pm
- Forum: Sensor-related questions
- Topic: heart rate sensor
- Replies: 19
- Views: 109020
- Thu Jul 22, 2010 5:26 pm
- Forum: Sensor-related questions
- Topic: RPM output - pulse vs freq
- Replies: 3
- Views: 7510
completely flat line, but when i went to check and move the input from rL to freq i put a meter on it and its got no volts, so im guessing the auto electrician neglected to reconnect the DL1 - tacho wire (there was a junction there) either way, when i run or reconnect the correct cable should i be p...
- Thu Jul 22, 2010 2:09 am
- Forum: Sensor-related questions
- Topic: RPM output - pulse vs freq
- Replies: 3
- Views: 7510
RPM output - pulse vs freq
changed ECUs -= the old one output to tach and i paralleled off that and into DL1 RPM input, worked all fine. The new one has what the factory manual describes as going up to approx 5 volts during operation. Aftermarket tacho works, DL1 doesnt. I'm thinking that the 5v signal has a freq in it - sho...
- Sun Jul 18, 2010 5:43 am
- Forum: General support questions
- Topic: DL1 users in Australia??
- Replies: 6
- Views: 11485
- Sun Jul 18, 2010 5:27 am
- Forum: Sensor-related questions
- Topic: heart rate sensor
- Replies: 19
- Views: 109020
just looking @ your engine restart after your spin you have a huge EMF discharge that pissed your cameras - definitely some need for RF choking devices around there - are you using shielded cable for your data stuff? belden 8723 with a shielded ground wire is always handy:) didnt know you drove a m...
- Sun Jul 18, 2010 4:54 am
- Forum: Sensor-related questions
- Topic: heart rate sensor
- Replies: 19
- Views: 109020
yah ive seen odd readings when used with different brands of exercise machines - also ive seen HR displayed on a treadmill when i wasnt wearing the polar sender - someone 2 metres away was! conductive gel sounds like fun, ive been known the soak my chest strap in water before exercise and it works ...
- Fri Jul 16, 2010 3:48 pm
- Forum: Sensor-related questions
- Topic: heart rate sensor
- Replies: 19
- Views: 109020
- Fri Jul 16, 2010 3:07 pm
- Forum: General support questions
- Topic: DL1 users in Australia??
- Replies: 6
- Views: 11485
- Tue Mar 16, 2010 11:03 am
- Forum: Sensor-related questions
- Topic: heart rate sensor
- Replies: 19
- Views: 109020
fyi. i dont work for them, havent dealt with them, only researched the issue and thought that the product may well work with a DL1. couple of things: 1. i would make up an adaptor plug so you dont have to chop the cable on the receiver - this way you can sell it when u are finished, or use it @ the ...
- Sun Nov 08, 2009 9:25 am
- Forum: General support questions
- Topic: Logging Air/Fuel ratio (Lambda)
- Replies: 6
- Views: 12320
okay - im new to this variable equations thing - im guessing i put the equation in data/variable manager/sensor type/units: ? i've put the '0.5+(X/5) in there and the numbers look meaningful - how do i go about changing this to read AFR so it looks the same as what I see on my AFR gauge, and on the ...
- Sun Nov 08, 2009 8:17 am
- Forum: Sensor-related questions
- Topic: heart rate sensor
- Replies: 19
- Views: 109020
i thought it would be interesting as well - did some research, rowing sport uses this sort of stuff - the chest straps spit out a magnetic pulse on each beat, the heart rate monitor type watch we wear when exercising picks up these pulses and counts then displays on the watch face. The box you can b...