Search found 9 matches

by Stratocaster
Mon Apr 14, 2014 10:17 pm
Forum: General support questions
Topic: Config help DL1 MK3
Replies: 1
Views: 4526

Config help DL1 MK3

I have a new DL1 MK3. When I read the current configuration, and make the needed changes to support my installation, sensors, ECU adapter and dash and then save the changes, I am greeted with a list of errors (6). I found two of the 1. Output drivers used but not enabled in the device This I underst...
by Stratocaster
Fri Apr 04, 2014 2:41 pm
Forum: General software support
Topic: "Swap file problem" starting analysis software
Replies: 4
Views: 14201

Okay - great news that it is working. WRT to why do we use a swap file, it complicated but the short version is although there is lots of memory in your PC there isn't always enough available to applications. Also on older OS's (eg XP which is still very popular) the maximum addressable space is on...
by Stratocaster
Tue May 18, 2010 3:42 am
Forum: Installation questions
Topic: AEM / DL1 interface problem
Replies: 1
Views: 6012

Mike

E-mail me your contact info and I will help you get things setup.

Jeff At rickS2k dot com
by Stratocaster
Fri Apr 16, 2010 3:06 pm
Forum: Installation questions
Topic: AEM ECU interface, DL1 and DASH2 Display issues
Replies: 4
Views: 11408

I don't understand why I would disable both the memory card and Serial port? I assume that if the ECU cable is sending the RPM data, I would want that enbaled? No? Please clarify. Nevermind, I figured it out. The DL1 settings are for output of the channel. So to disable the channel, you turn both o...
by Stratocaster
Fri Apr 16, 2010 2:30 pm
Forum: Installation questions
Topic: AEM ECU interface, DL1 and DASH2 Display issues
Replies: 4
Views: 11408

Which firmware version is on the DL1? There was a change in the latest formware of the DL1, see below to see if this works for you. Also make sure you select the correct RPM source on the DASH2 itself, this is done through the DASH2 menu not the configuration software, see here: m "With previo...
by Stratocaster
Fri Apr 16, 2010 5:38 am
Forum: Installation questions
Topic: AEM ECU interface, DL1 and DASH2 Display issues
Replies: 4
Views: 11408

AEM ECU interface, DL1 and DASH2 Display issues

OK, I have everything working, but I had to work around something and I wanted to know if I should have needed to. I can see the Engine Speed channel using the Lite Monitor. So I know that the ECU is streaming it to the DL1. But when I configure the DASH2 to display it, I get nothing on the DASH2. S...
by Stratocaster
Fri Apr 16, 2010 5:32 am
Forum: Installation questions
Topic: Dash2 and AEM ECU data scaling?
Replies: 1
Views: 5507

Nevermind. I figured it out. I used the Graph section and I entered 0=32 and 100=212. That calculated it for me.
by Stratocaster
Wed Apr 14, 2010 3:21 pm
Forum: Installation questions
Topic: How to configure an AEM ECU to talk to a RT ECU interface
Replies: 1
Views: 6834

How to configure an AEM ECU to talk to a RT ECU interface

The AEM ECU is configured from the factory to NOT stream data out the serial port. So to use the RT ECU cable, you have to configure the AEM ECU to stream the data that RT understand. So I thought I would share exactly how to do this as I found this hard to figure out with the limited data posted he...
by Stratocaster
Wed Apr 14, 2010 3:10 pm
Forum: Installation questions
Topic: Dash2 and AEM ECU data scaling?
Replies: 1
Views: 5507

Dash2 and AEM ECU data scaling?

The default scaling is for the Water temp channel is y= +1x. This will display the temp vaules in Celsuis. I would like to display them in Fahreneit. I know that if X = Celsuis and Y = Fahreneit, then y = x * 1.8 + 32 will give the results need. But how would I enter this into the Dash 2 scaling, en...

Go to advanced search