Search found 8 matches

by Scott SkylineGTR
Mon Feb 22, 2016 5:33 pm
Forum: General support questions
Topic: Motec M880-Dash 2 CAN help
Replies: 1
Views: 4619

Motec M880-Dash 2 CAN help

Hi folks. Having real difficulty in trying to understand the steps I need to take to get my Motec M880 talking to my Dash2. TBH, the knowledge base isn't all that helpful IMHO. I have configured my ECU to output as per R/T datasheet i.e. CAN 0 DATA - 8 CAN 0 ADDRESS - 1520 CAN 0 Transfer Rate - 50 I...
by Scott SkylineGTR
Tue Jul 09, 2013 8:57 pm
Forum: General support questions
Topic: Dash2 and DL1 issues
Replies: 2
Views: 5575

Thanks for the reply...

I shall check the DL1 and reflash the Dash2 (despite both having latest firmware updated)

I shall report back on progress.

Failing that i will probably send both to RT to get checked....

Feeling quite disappointed at the moment... :(


Scott
by Scott SkylineGTR
Sat Jul 06, 2013 11:52 pm
Forum: General support questions
Topic: Dash2 and DL1 issues
Replies: 2
Views: 5575

Dash2 and DL1 issues

Eventually got around to installing Dash2 and DL1 (MK1) in my Skyline track car. Physically installed both units, wired them up appropriately and reflashed both with the latest firmware (as I have had them for a couple of years stored in their cases) and connected both via serial. Strangely, I did N...
by Scott SkylineGTR
Sun Jan 09, 2011 10:28 pm
Forum: Sensor-related questions
Topic: Nissan sensor questions
Replies: 14
Views: 25439

Thanks Rob. I've managed to find a sensor in the RS components catalogue which looks physically identical to the sensor RT supply with the same spec ( I assume it's the same one!! .. This looks like it will fit the aperture in my rear diff housing where the stock ABS vrs sensor resides. Question is,...
by Scott SkylineGTR
Thu Dec 23, 2010 7:37 pm
Forum: Sensor-related questions
Topic: Nissan sensor questions
Replies: 14
Views: 25439

Thanks for the replies folks.
So, got the RPM sorted (I will use standard dash RPM feed and see how I get on).
As for wheel speed the rear driveshaft ABS ring has , what looks like, a nice trigger so the question is...what sensor would folks recommend I use thats compatible with the DL1/DASH2 ??
by Scott SkylineGTR
Sun Dec 12, 2010 10:08 pm
Forum: Sensor-related questions
Topic: Nissan sensor questions
Replies: 14
Views: 25439

PFC is stand alone. I have a pinout somewhere, just need to look it out :D

Thanks again..
by Scott SkylineGTR
Sun Dec 12, 2010 5:51 pm
Forum: Sensor-related questions
Topic: Nissan sensor questions
Replies: 14
Views: 25439

Thanks for the reply.... TBH, I'd rather utilise the ABS sensors if possible with an appropriate converter box if needed. As for RPM, I dont have an oscilloscope or have access to one either unfortunately...I suspect that the ECU may well have an RPM output that I could utilise. Alternatively the st...
by Scott SkylineGTR
Sat Dec 11, 2010 10:47 pm
Forum: Sensor-related questions
Topic: Nissan sensor questions
Replies: 14
Views: 25439

Nissan sensor questions

Hi folks, I have bought a DASH 2 to use in my R32GTR track car.... The car currently runs an Apexi PowerFC and I realise there is no ECU cable avaiable to use to connect to the DASH2. I intend to change the ECU at some point down the line (mid-end 2011) to a SYVECS S6 or Life Racing F-88 which shoul...

Go to advanced search