Search found 69 matches
- Thu Jun 14, 2018 2:47 pm
- Forum: General support questions
- Topic: Horsepower Calculation Q's
- Replies: 0
- Views: 243941
Horsepower Calculation Q's
Hi - I'm trying to determine/confirm that I have an engine air intake issue at higher speeds (>100mph) by using the HP tool in analysis. When I ask it to perform the power calc, the number (380hp) matches my dyno number. I also get this same number when accelerating out of turns. But, when I check H...
- Fri Jun 08, 2018 5:59 pm
- Forum: General software support
- Topic: DASH2Pro Signal Manipulation
- Replies: 5
- Views: 27504
Re: DASH2Pro Signal Manipulation
"high rpm" is if you are pulling the signal from the spark plug wires, "low rpm" is for a signal from the computer.
- Fri Jun 08, 2018 5:58 pm
- Forum: General software support
- Topic: DASH2Pro Signal Manipulation
- Replies: 5
- Views: 27504
Re: DASH2Pro Signal Manipulation
here are the settings
- Fri Jun 08, 2018 1:58 pm
- Forum: General software support
- Topic: DASH2Pro Signal Manipulation
- Replies: 5
- Views: 27504
Re: DASH2Pro Signal Manipulation
The OEM signal works fine on a friend's D2Pro that I installed. I can send you the settings if you message me your info. The water temp signal, as you've discovered, is quite curious. You can add a dedicated temp sensor to the rear of the passenger side head to get full range readings and avoid that...
- Mon May 07, 2018 1:25 pm
- Forum: Sensor-related questions
- Topic: Strain gauges on DL1
- Replies: 5
- Views: 53603
Re: Strain gauges on DL1
I have no experience (or affiliation) with this - but it is something to consider: http://www.izzeracing.com/products/stra ... ifier.html
- Wed Mar 28, 2018 8:19 pm
- Forum: General support questions
- Topic: Syvecs S6GP Data
- Replies: 10
- Views: 23136
Re: Syvecs S6GP Data
Ok, you can just pay for as many 15 channel CAN licenses that you need (that will take care of the DL1 hardware side). On the DL1 software side, you will need to set it up to receive the CAN data and then map the incoming CAN data to a DL1 channel. I've attached a screenshot that will get you going....
- Tue Mar 27, 2018 8:19 pm
- Forum: General support questions
- Topic: Syvecs S6GP Data
- Replies: 10
- Views: 23136
Re: Syvecs S6GP Data
which version DL1 do you have (is it a Mk3 with a direct CAN input)?
- Fri Mar 16, 2018 3:10 am
- Forum: General support questions
- Topic: Syvecs S6GP Data
- Replies: 10
- Views: 23136
Re: Syvecs S6GP Data
A current DL1 that has a CAN bus input is able to receive any and all info sent by the S6 via CAN, correct (assuming enough of the 15 CAN channel licenses are purchased)? The 15 channel limitation is only with the CAN to serial interface, right?
- Mon Jun 13, 2016 3:36 pm
- Forum: General software support
- Topic: Getting simulation to work effectively with a Caterham
- Replies: 1
- Views: 14038
Re: Getting simulation to work effectively with a Caterham
I am interested as well, I have had the same issue with simulation times being unreasonably quick.
- Fri May 27, 2016 1:20 pm
- Forum: General software support
- Topic: Analysis v8.5.369
- Replies: 4
- Views: 16015
Re: Analysis v8.5.369
up, would really like to have the tabs back.
Thanks.
Thanks.
- Fri May 06, 2016 5:13 pm
- Forum: General support questions
- Topic: Displaying Gear from ECU
- Replies: 4
- Views: 11597
Re: Displaying Gear from ECU
Try to send the gear channel info to one of the "aux" variables (ignore the R-T label for that channel).
- Thu May 05, 2016 4:30 pm
- Forum: General support questions
- Topic: Displaying Gear from ECU
- Replies: 4
- Views: 11597
Re: Displaying Gear from ECU
are you sending a CAN stream or serial stream to the Dash 4? If CAN, then yes, no issues. If serial, you will need to feed a DL1 with the info, buy a CAN license (which I assume you have, if you are getting other channels from the ECU), and then setup gear channel in the CAN config and in the variab...
- Tue Mar 29, 2016 7:26 pm
- Forum: Sensor-related questions
- Topic: How to set up additional Sensors connected to analouge inputs?
- Replies: 1
- Views: 14735
Re: How to set up additional Sensors connected to analouge inputs?
What did you set for your channel mins and maxs?
- Tue Mar 08, 2016 12:40 am
- Forum: General support questions
- Topic: DL1 PWM Output/PWM fuel controller equation
- Replies: 0
- Views: 58551
DL1 PWM Output/PWM fuel controller equation
Hello - I have a car with two fuel tanks (a left and a right) that will be running ethanol and gas in varying amounts and also various states of de-tune (depending on the power to weight class entered for a given event). I have one fuel pump in each tank that pumps to a surge tank, and then connecte...
- Fri Mar 04, 2016 12:43 am
- Forum: General support questions
- Topic: Dash4/Video4 Y Cable Question
- Replies: 0
- Views: 58082
Dash4/Video4 Y Cable Question
Hello - I would appreciate if someone could confirm the internal wiring on the Y cable (YCAB001) -- on the DB9 connector that connects to the DL1, does each branch of the cable simply share pins 2 (Rx1), 3 (Tx1) and 5 (GND), with pin 7 (12v) only going to the Dash4 branch? Or is there a passthrough ...