Custom harnesses often have splices for power and ground signals. Now that you know what you want to measure and where the sensors go, lay out a custom harness, and build in the splices you need into the harness.
This can look very neat and tidy if done right.
Search found 21 matches
- Wed Feb 26, 2014 11:18 pm
- Forum: Installation questions
- Topic: DL1 - Multiple Sensor - Messy wiring
- Replies: 2
- Views: 13802
- Fri Nov 01, 2013 11:01 pm
- Forum: General software support
- Topic: open course plots offset
- Replies: 4
- Views: 10171
- Sat Mar 19, 2011 2:37 pm
- Forum: General support questions
- Topic: Dash 3 Unreliable Lap/Sector Times
- Replies: 20
- Views: 32833
- Fri May 29, 2009 8:47 pm
- Forum: General support questions
- Topic: Minimum pulse width on DL1/DL2 RPM input?
- Replies: 5
- Views: 9618
- Fri May 29, 2009 6:49 pm
- Forum: General support questions
- Topic: Minimum pulse width on DL1/DL2 RPM input?
- Replies: 5
- Views: 9618
Minimum pulse width on DL1/DL2 RPM input?
We have been trying to use a wheel speed sensor to sense a magnet on the flywheel of a Formula Ford 1600 engine. We are getting good RPM reading at low RPM, but at higher RPM it just stops altogether. Is there a minimum low-going pulse width that the RPM signal must have in order to be detected prop...
- Wed Oct 18, 2006 11:35 pm
- Forum: General support questions
- Topic: RPM scaling
- Replies: 12
- Views: 23648
A setting of .5 ignition pulses per revolution would be correct if you were picking up the signal from a single spark plug wire (or a coil on plug setup). If you are using a coil/distributor and using the coil input then you would use the value of 2. So, both values could be used for a 4-stoke 4-cyl...
- Wed Oct 11, 2006 12:01 am
- Forum: General support questions
- Topic: Random lines in GPS data
- Replies: 1
- Views: 6181
Random lines in GPS data
I have seen large "position deltas" that result is wide-ranging random lines in a track map view. Sometimes this is caused by logging before the GPS lock has been obtained, and in one case it was a bad mounting location that obscured the antennas view of the sky. However, sometimes it just seems to ...
- Sun Oct 08, 2006 4:55 pm
- Forum: Sensor-related questions
- Topic: Gear sensor for race bike
- Replies: 1
- Views: 7300
If you bike has a gear-position potentiometer (GSX-R and ZX-10R do I believe), then you can just connect to the output of that sensor. Otherwise, you may wish create a math channel with something like (gear = speed/(RPM/1000)) the ouput will be a "stair-stepped" graph each level representing a parti...
- Thu Sep 28, 2006 4:42 pm
- Forum: General support questions
- Topic: Analysis v6.3.81 just released :)
- Replies: 2
- Views: 7167
Any changes other than the AX22 and SPEEDBOX-RTK support mentioned in the revision notes?
http://www.race-technology.com/WebPage2 ... nList.html
http://www.race-technology.com/WebPage2 ... nList.html
- Tue Sep 26, 2006 9:35 pm
- Forum: General support questions
- Topic: RPM scaling
- Replies: 12
- Views: 23648
What is the value of the "Ignition Pulses Per Revolution" field in Data/Vehicle Options/RPM-tab? I would expect a value of 2 would be correct for your engine. (4 cylinder, 4 stroke). The ignition normaly fires twice for each revolution of the engine. What does the RPM trace look like? Is it smooth, ...
- Fri Sep 22, 2006 11:00 pm
- Forum: General software support
- Topic: DL1 configuration
- Replies: 2
- Views: 7525
Save the file as "SETUP.BIN" and put it on top level of your compact flash card. You need to start the DL1 with the card inserted and it will read the SETUP.BIN file and re-flash it's internal settings. You can now remove the SETUP.BIN file and the DL1 will continue to use that configuration until a...
- Wed Sep 20, 2006 5:32 am
- Forum: General support questions
- Topic: Error 52
- Replies: 8
- Views: 17919
- Wed Sep 13, 2006 11:19 pm
- Forum: General support questions
- Topic: DL1 Vers 7 Firmware and Setup files
- Replies: 5
- Views: 10318
- Wed Sep 13, 2006 5:59 pm
- Forum: General support questions
- Topic: DL1 Vers 7 Firmware and Setup files
- Replies: 5
- Views: 10318
DL1 Vers 7 Firmware and Setup files
We have a customer with a new DL1 that had version 7-3 Firmware installed. While it logs data, there is no GPS map drawn. A couple of observations: - With the vers 7 Firmware (either 7-3 or 7-5), the GPS Lock light flashes quickly. Using the older firmware in another using (version 5-2), we get the ...
- Tue Aug 15, 2006 6:03 pm
- Forum: General support questions
- Topic: Error -56, corrupt files when loading raw run data
- Replies: 3
- Views: 7431
Error -56, corrupt files when loading raw run data
We have a customer that is reporting he get's error -56 and a report of a corrupted data file when he attempts to load a data file from the compact flash. I haven't encountered this problem, so I verified that he had formatted the CF card as FAT16 before the run. Anyone know what this problem might ...