Search found 24 matches

by thokes82
Mon Jun 03, 2019 10:25 am
Forum: Sensor-related questions
Topic: GPS data jumps (same spot, every lap)
Replies: 10
Views: 72399

Re: GPS data jumps (same spot, every lap)

Sorry, I cannot figure it out. Can the problem be linked to the fact that RTLive is not really using the accelerometers but the calculated GPS based values for display? Mounting is correct and setting in Analysis is correct too. Please also confirm that there is not option in RTLive config software ...
by thokes82
Tue May 28, 2019 1:11 pm
Forum: Sensor-related questions
Topic: GPS data jumps (same spot, every lap)
Replies: 10
Views: 72399

Re: GPS data jumps (same spot, every lap)

Same Problem here. But with RTLive I am not able to solve it the way you describe. I can change the orientations settings in the analysis only as the RTLive config software doesn't provide these options. The "back" setting should normally be the correct one for my setup. I tried different other sett...
by thokes82
Sun Apr 28, 2019 6:10 pm
Forum: General support questions
Topic: RTLive: Reset "Integrate" Function
Replies: 1
Views: 5480

RTLive: Reset "Integrate" Function

Hi, I would like to know if there is a way to reset a can channel that I integrate. I would like to zero the number without stopping the log or shutting down the logger (RTLIVE). It shall be a push button. As a first step I would accept to reset all integration values with the same operation. If the...
by thokes82
Thu Feb 01, 2018 7:45 pm
Forum: Installation questions
Topic: Aux Messages on RTLive
Replies: 1
Views: 27646

Aux Messages on RTLive

Hi,
there seems to be an error on your Wiki. The Aux Messages on this page appear to be in reality Aux7-12 instead of 14-19.
http://www.race-technology.com/wiki/ind ... uxMessages
by thokes82
Fri Jan 08, 2016 7:46 am
Forum: General software support
Topic: Simulation makes weird things
Replies: 5
Views: 16418

Hello. Where you able to look at my screenshot? It seems that the sim speed is not calculated corectly. I was trying to input the power curve into sim settings and edited the gear ratios, drag etc. After the re-calculation the sim time is far off the real time. I think it is because the sim speed is...
by thokes82
Thu Jan 07, 2016 4:28 pm
Forum: General software support
Topic: Simulation makes weird things
Replies: 5
Views: 16418

I have sent a request to the support. This is the answer I got: Dear Valued Customer, This is an automated response, this email address is no longer in use due to the huge amount of spam that it was attracting. In order for us to provide you with more accurate replies we have decided to accept suppo...
by thokes82
Wed Jan 06, 2016 2:07 pm
Forum: General software support
Topic: Simulation makes weird things
Replies: 5
Views: 16418

Simulation makes weird things

m My simulation is broken and I can not see how I can fix it. No matter what Simulation settings or Variable definitions I used, it seems not to react at all. The simulated time is far off the real time and it does not change anymore when I change the cars power curve for example. What do I have to ...
by thokes82
Thu Nov 20, 2014 1:51 pm
Forum: General support questions
Topic: Megasquirt MS3 again, CAN can work now!!
Replies: 3
Views: 7620

CAN .dbc File For Megasquirt MS3 and MS2

http://www.msextra.com/doc/pdf/Megasqui ... -10-27.dbc

Here above you find the .dbc file for MS2extra Firmware 3.4 and newer
and MS3 Firmware 1.4 and newer
by thokes82
Fri Sep 19, 2014 9:07 am
Forum: General support questions
Topic: Corrupted CF card after one logging session...
Replies: 5
Views: 9548

Had the same... Take another CF Card even if scandisk and other things do not find errors. Somehow it worked in my case.
by thokes82
Wed Aug 20, 2014 5:11 pm
Forum: Installation questions
Topic: DL1Sport, Dash 2 and CAN ECU Adapter
Replies: 5
Views: 13629

Update: I used a Sandisk 4Gb Card lying around and it worked imediatly. So, Topic two is considered to be solved. Also I used a SETUP.BIN file created with the DL1 tool (instead of DL1 Sport). Works good. Seems that it is ok now with communication between Dash and DL1Sport. I will re-check on three ...
by thokes82
Thu Aug 14, 2014 2:28 pm
Forum: Installation questions
Topic: DL1Sport, Dash 2 and CAN ECU Adapter
Replies: 5
Views: 13629

I bought it from Matthias Holle, your rep in Germany. This might be relevant information for you but not for me.
Again:
2. Any Cards proven to explicitly not work?
1. It is a DL1 Sport. So I did not use the DL1 tool. Should I? Why is there a special program for setting the DL1 Sport then?
by thokes82
Thu Aug 14, 2014 1:25 pm
Forum: Installation questions
Topic: DL1Sport, Dash 2 and CAN ECU Adapter
Replies: 5
Views: 13629

1. It is a DL1 Sport. So I did not use the DL1 tool. Should I? Why is there a special program for setting the DL1 Sport then? 2. It is a Sandisk 8GB. I got it with the package. I am trying a different one tomorrow and report back. (Any ones proven to explicitly not work?) I ran Scandisk on the card ...
by thokes82
Wed Aug 13, 2014 1:38 pm
Forum: Installation questions
Topic: DL1Sport, Dash 2 and CAN ECU Adapter
Replies: 5
Views: 13629

DL1Sport, Dash 2 and CAN ECU Adapter

Hello, I have been playing with my Dash2, my DL1Sport for about a year and since 2 months I added an ECU Adapter (CAN) because my serial adapter based on Arduino didn't really work. However it turns out that my problems seem not to be related to the Arduino. 1. My Dash2 crashes. When I leave my Dash...
by thokes82
Mon Jun 09, 2014 7:11 am
Forum: General support questions
Topic: Megasquirt MS3 again, CAN can work now!!
Replies: 3
Views: 7620

My RT can Adapter sends not a single Byte on the lite monitor. I just do not know where to start searching. Would the adapter send anything even if there is no can connection?
by thokes82
Fri Apr 18, 2014 4:10 pm
Forum: General support questions
Topic: Megasquirt MS3 again, CAN can work now!!
Replies: 3
Views: 7620

Megasquirt MS3 again, CAN can work now!!

Hi gents, I would like to ask the support team to look into the following document and ask a programmer to give some feedback too. MS3 and MS2 are with their newest firmware finally able to send CAN commands according to a standard protocol. m This is great news. Can somebody tell me if your CAN ada...

Go to advanced search