Search found 13 matches
- Mon Feb 08, 2016 7:23 pm
- Forum: Sensor-related questions
- Topic: change reading from bar to psi ?
- Replies: 2
- Views: 17352
change reading from bar to psi ?
I have a dash2 with rt sensors and would like to know if its possible to change the oil pressure readout from bar to psi. couldn't find anything in the help section so asking here.
- Fri Sep 18, 2015 7:01 pm
- Forum: Sensor-related questions
- Topic: pull up resistor for rt sensor
- Replies: 1
- Views: 11105
pull up resistor for rt sensor
do I need a pull up resistor with a rt oil pressure sensor wired direct to the dash2 ?
- Wed Sep 16, 2015 6:03 pm
- Forum: Sensor-related questions
- Topic: odd water temp reading
- Replies: 0
- Views: 47404
odd water temp reading
water temp reads 92/3 f when engine is stone cold? using a standard rt sensor any ideas anyone?
- Sat May 02, 2015 7:02 am
- Forum: Sensor-related questions
- Topic: no mph/wheel speed/dash2
- Replies: 2
- Views: 11286
- Fri May 01, 2015 7:01 pm
- Forum: Sensor-related questions
- Topic: no mph/wheel speed/dash2
- Replies: 2
- Views: 11286
no mph/wheel speed/dash2
just installed the rt wheel speed sensor but get 0 mph on the dash 2. led on the sensor blinks when the target bolt passes but no mph readout on the dash. I put the correct pulses per mile into the dash via the buttons as per the manual. checked the wiring, still nothing. 5v reference shows 4.5 volt...
- Thu Apr 30, 2015 6:57 am
- Forum: Sensor-related questions
- Topic: aem pressure sensor resistance
- Replies: 4
- Views: 13121
- Wed Apr 29, 2015 8:30 pm
- Forum: Sensor-related questions
- Topic: aem pressure sensor resistance
- Replies: 4
- Views: 13121
- Wed Apr 29, 2015 7:20 pm
- Forum: Sensor-related questions
- Topic: aem pressure sensor resistance
- Replies: 4
- Views: 13121
aem pressure sensor resistance
I have an aem pressure sensor p/n 30-2131-150 that I am using for oil pressure on my dash2. although the sensor came with an instruction sheet it doesn't say the resistance in ohms , so I don't know what size pull up resistor to use. can anyone shed any light on this? It has the supply current, supp...
- Wed Apr 15, 2015 7:55 pm
- Forum: Sensor-related questions
- Topic: 5v reference on dash 2
- Replies: 3
- Views: 11538
- Wed Apr 15, 2015 7:08 pm
- Forum: Sensor-related questions
- Topic: 5v reference on dash 2
- Replies: 3
- Views: 11538
5v reference on dash 2
bit of a newbie question, but how many sensors will the 5v reference on the dash 2 support. I have rt coolant temp sensor, rt wheel speed sensor, vdo dip pipe fuel sender and an aem oil pressure sensor to connect up. Do I simply add the max milli amps each sensor will use and see if it is within 50m...
- Fri Feb 06, 2015 7:39 pm
- Forum: Sensor-related questions
- Topic: wiring sensors to dash 2
- Replies: 3
- Views: 14477
- Wed Feb 04, 2015 8:13 pm
- Forum: Sensor-related questions
- Topic: wiring sensors to dash 2
- Replies: 3
- Views: 14477
wiring sensors to dash 2
electrics are definitely not my strong point, so need some help explaining some basic wiring, namely the sensors. How do I wire the 3 wire oil pressure sensor to the dash2 ? i have read that i may need a resistor? I assume 1 wire is ground, and another goes to the analogue input on the dash2 but tha...
- Mon Jan 19, 2015 7:35 pm
- Forum: Installation questions
- Topic: 1 wire alternator/voltage wiring question
- Replies: 1
- Views: 11576
1 wire alternator/voltage wiring question
I have a 1 wire alternator, and am not sure how to wire the voltage readout on the dash 2 to this alternator. anyone done this or know how to?