Search found 53 matches

by peterguk
Tue May 21, 2019 7:40 am
Forum: How do I...
Topic: odometer setup
Replies: 3
Views: 57

Re: odometer setup

Email RT. IIRC they can do that for you. A charge may be payable.
by peterguk
Tue Apr 30, 2019 5:45 pm
Forum: How do I...
Topic: DASH2 move from DAT to CMG
Replies: 4
Views: 280

Re: DASH2 move from DAT to CMG

Huh? What's the big deal? I've done 3 so far. Each one less than 40 minutes. New software so much easier to use.

But then i had all the settings in a spreadsheet.

IIRC, took me 5 hours to upgrade my last Windose PC...
by peterguk
Fri Apr 26, 2019 9:39 pm
Forum: How do I...
Topic: DASH2 move from DAT to CMG
Replies: 4
Views: 280

Re: DASH2 move from DAT to CMG

AFAIK, when you upgrade to latest firmware, you start off with a blank sheet and have to rebuild your config from scratch, channel by channel, sensor by sensor.
by peterguk
Thu Oct 04, 2018 10:30 pm
Forum: General support questions
Topic: Upload Calibration & Lost ECU CAN Interface Data
Replies: 4
Views: 4611

Re: Upload Calibration Lost ECU CAN Interface Data

Well after a second look it looks like the TWIN 350 emblems are obsolete as well.  Double suck… Are there any custom graphics makers out there that you can email a picture to and have them make you something similar?
Few too many Bud Lights? :|
by peterguk
Sun Sep 16, 2018 4:36 pm
Forum: General support questions
Topic: Revs higher than 9000rpm and fuel sending question - motorbike related
Replies: 5
Views: 4085

Re: Revs higher than 9000rpm and fuel sending question - motorbike related

I couldn't see on the software about programming in the odometer reading so that it can continue from where my analogue instrument cluster leaves off.
You can't. AFAIK you need to send the unit to RT for them to do for you.
by peterguk
Sun Sep 09, 2018 9:19 pm
Forum: General support questions
Topic: Need to update settings on Dash2 v9.3.4
Replies: 7
Views: 4530

Re: Need to update settings on Dash2 v9.3.4

Send me an email to noblem500 AT gmail.com and i'll send you a copy of the manual.
by peterguk
Sun Sep 09, 2018 10:02 am
Forum: General support questions
Topic: Need to update settings on Dash2 v9.3.4
Replies: 7
Views: 4530

Re: Need to update settings on Dash2 v9.3.4

Have you tried reading the manual?

The tasks you're wanting to do are normal for anyone setting a Dash2 up and are pretty simple if you follow the manual.
by peterguk
Wed Aug 29, 2018 10:34 pm
Forum: Pre-sales product questions
Topic: Dash2 Italiano
Replies: 18
Views: 10709

Re: Dash2 Italiano

Use simple Italian and we can translate
How do I replace the odometer reading with the BEST LAP AND last lap time.
by peterguk
Thu Aug 09, 2018 6:30 pm
Forum: Installation problems
Topic: Dash 2 sensors set up
Replies: 4
Views: 11638

Re: Dash 2 sensors set up

Have you got the temperature/resistance curve for the sensor?

If not, stick it in ice and boiling water and measure resistance. Do same in a saucepan for 2 or 3 more temperatures, say at 20 40 and 60 degrees.

Then input the data in the sensor configuration. Job done.
by peterguk
Tue Jul 31, 2018 11:56 pm
Forum: Installation problems
Topic: Dash2 Set up Help in york
Replies: 2
Views: 3748

Re: Dash2 Set up Help in york

Hi Jim

I'm in Barnsley and can easily pop up to you.

Send me an email to noblem500 AT gmail.com (replace the AT and delete the spaces) with a phone number and i'll give you a call.

Peter
by peterguk
Mon Apr 23, 2018 8:17 pm
Forum: General support questions
Topic: Problem connecting PC to Dash2
Replies: 12
Views: 8808

Re: Problem connecting PC to Dash2

IIRC, i had to perform a firmware upgrade to enable it to connect to 8.5.

Email support direct?
by peterguk
Thu Dec 21, 2017 10:56 pm
Forum: How do I...
Topic: Hondata CAN Input
Replies: 4
Views: 4521

Re: Hondata CAN Input

Have you emailed support direct? They normally reply very quickly.
by peterguk
Fri Nov 03, 2017 9:02 pm
Forum: Installation problems
Topic: Dash 2 firmware
Replies: 4
Views: 4632

Re: Dash 2 firmware

9.1.0 sounds old. I've been using 9.3.5 for ages.
by peterguk
Mon Aug 21, 2017 5:59 pm
Forum: General support questions
Topic: Dash2 Equation for kPa to psi
Replies: 2
Views: 1780

Re: Dash2 Equation for kPa to psi

Dan

Thank you for your prompt reply.

So the lookup table will work with values other than actual measured voltages!

I didn't realise the solution was as simple as it is!

Excellent! Thanks again!

Peter
by peterguk
Fri Aug 18, 2017 8:03 pm
Forum: General support questions
Topic: Dash2 Equation for kPa to psi
Replies: 2
Views: 1780

Dash2 Equation for kPa to psi

MoTeC M4 with RT serial adaptor to DL1 and Dash2. ECU outputs manifold pressure in kPa. I want to display boost in psi. I can't create an equation from a table as i don't have voltages to input. So i need to enter a equation that reflects the conversion from kPa to psi. Can anyone give me the equati...

Go to advanced search