Search found 42 matches

by peterguk
Thu Dec 21, 2017 10:56 pm
Forum: How do I...
Topic: Hondata CAN Input
Replies: 4
Views: 92

Re: Hondata CAN Input

Have you emailed support direct? They normally reply very quickly.
by peterguk
Fri Nov 03, 2017 9:02 pm
Forum: Installation problems
Topic: Dash 2 firmware
Replies: 3
Views: 153

Re: Dash 2 firmware

9.1.0 sounds old. I've been using 9.3.5 for ages.
by peterguk
Mon Aug 21, 2017 5:59 pm
Forum: General support questions
Topic: Dash2 Equation for kPa to psi
Replies: 2
Views: 446

Re: Dash2 Equation for kPa to psi

Dan

Thank you for your prompt reply.

So the lookup table will work with values other than actual measured voltages!

I didn't realise the solution was as simple as it is!

Excellent! Thanks again!

Peter
by peterguk
Fri Aug 18, 2017 8:03 pm
Forum: General support questions
Topic: Dash2 Equation for kPa to psi
Replies: 2
Views: 446

Dash2 Equation for kPa to psi

MoTeC M4 with RT serial adaptor to DL1 and Dash2. ECU outputs manifold pressure in kPa. I want to display boost in psi. I can't create an equation from a table as i don't have voltages to input. So i need to enter a equation that reflects the conversion from kPa to psi. Can anyone give me the equati...
by peterguk
Tue Aug 15, 2017 8:08 pm
Forum: General support questions
Topic: Clock
Replies: 5
Views: 566

Re: Clock

rodgling wrote:I got this working (on a dash2pro, but I'd think it would work on a dash2 if you have GPS data) - see this thread: https://www.race-technology.com/forum/v ... f=2&t=2802


Thanks. I found that but only GMT?
by peterguk
Sat Aug 12, 2017 1:51 pm
Forum: General support questions
Topic: Clock
Replies: 5
Views: 566

Re: Clock

Please post the solution here for all to see.

I was under the impression this could not be done???

Would be great if it could.
by peterguk
Mon Jul 24, 2017 7:07 pm
Forum: General support questions
Topic: kann hier jemand deutsch?
Replies: 3
Views: 356

Re: kann hier jemand deutsch?

Wir brauchen mehr Informationen.

Sind die Sensoren von Race Technology?
by peterguk
Mon Jul 17, 2017 9:27 pm
Forum: General support questions
Topic: LCD Screen not lighting
Replies: 7
Views: 626

Re: LCD Screen not lighting

You appear to have the pins mirrored vertically.

Check out the diagram page 8.

e.g. pin 14 (fog light) is in mirrored position of pin 7 (main beam)
by peterguk
Fri Jul 14, 2017 5:02 pm
Forum: General support questions
Topic: LCD Screen not lighting
Replies: 7
Views: 626

Re: LCD Screen not lighting

If i remember correctly, there are two firmware versions for Dash2:

a) backlight is only lit when sidelight input (connector2, pin1) is 12V+ve

b) backlight is permanently lit when unit is switched on

Do you know which version you have?
by peterguk
Fri Jul 07, 2017 9:11 pm
Forum: Installation questions
Topic: Alternator warning light wire.
Replies: 2
Views: 391

Re: Alternator warning light wire.

You need to connect the Dash2 alternator warning light wire to the warning light (WL) wire on your alternator. It is an earth source, not live! When the alternator is not charging, the WL output wire is earthed inside the alternator. The alternator bulb in the regular dash is live on the other side ...
by peterguk
Thu Jun 01, 2017 10:13 pm
Forum: Pre-sales product questions
Topic: Dash2 Italiano
Replies: 12
Views: 1497

Re: Dash2 Italiano





by peterguk
Sat Apr 22, 2017 7:27 pm
Forum: Pre-sales product questions
Topic: Dash2 Italiano
Replies: 12
Views: 1497

Re: Dash2 Italiano

Usa semplice italiano e possiamo tradurre
by peterguk
Thu Feb 16, 2017 11:22 pm
Forum: Sensor-related questions
Topic: Wheel speed sensor question.
Replies: 4
Views: 538

Re: Wheel speed sensor question.

IMHO, i think you'll find the duty cycle of the teeth way too small.
by peterguk
Tue Jan 17, 2017 10:10 pm
Forum: General support questions
Topic: DL1 Sport / Dash 2 Display live data on PC
Replies: 7
Views: 1404

Re: DL1 Sport / Dash 2 Display live data on PC

A null modem cable has a nine pin connector at each end.

Google will assist you more.

Go to advanced search