Search found 7 matches

by Turbo Synthesis
Wed Jun 12, 2019 9:55 am
Forum: General support questions
Topic: Sending serial data to DL1 MkII
Replies: 2
Views: 9545

Sending serial data to DL1 MkII

Good morning, I have a question about sending serial data to a DL1 for it to include in a log file. We currently have a DL1 MkII in our endurance car, connected to an arduino fitted with a custom shield which has one RS232 channel and two CAN channels. The RS232 channel decodes the serial stream fro...
by Turbo Synthesis
Mon Nov 19, 2018 6:13 pm
Forum: General support questions
Topic: DL1 not logging RPM or Analogs
Replies: 2
Views: 8549

Re: DL1 not logging RPM or Analogs

Hi Martin,

Thanks for your response.

I rather suspected that might be the case. I'll contact sales and get it sent back to you. No point in having a spare if it can't be used as a spare !

Regards,

Gareth
by Turbo Synthesis
Sat Nov 17, 2018 5:33 pm
Forum: General support questions
Topic: DL1 not logging RPM or Analogs
Replies: 2
Views: 8549

DL1 not logging RPM or Analogs

Hi, I have 3 DL1 MKII's, 2 of which all appear to be functioning normally but the third one isn't logging any analog channels or RPM. I have the same SETUP.BIN file in all 3 of them. (Analog 1 to 8 100Hz Flash Card - 1Hz Serial, RPM 100Hz Flash Card - 10Hz Serial) When I look at the serial data in L...
by Turbo Synthesis
Thu Mar 15, 2018 9:51 am
Forum: General support questions
Topic: Ony seeing 'New Sector Time" at lap marker
Replies: 1
Views: 6076

Re: Ony seeing 'New Sector Time" at lap marker

Sorry, rookie mistake !

In my .lap file I'd allocated markers at the sector points, but not actually allocated sectors between the markers.
Once I did that I started getting channel 4 at each marker with Data 1 containing the marker number as expected.

Gareth
by Turbo Synthesis
Wed Mar 14, 2018 8:20 pm
Forum: General support questions
Topic: Ony seeing 'New Sector Time" at lap marker
Replies: 1
Views: 6076

Ony seeing 'New Sector Time" at lap marker

Hi, I have a DL1 MK2 that I'm currently setting up in time for this years Belcar Endurance championship. This may well just be my misunderstanding but is the serial port supposed to send out channel 4 (New Sector Time) every time I cross a matched marker or will it only do it at the lap marker? I'm ...
by Turbo Synthesis
Wed Mar 07, 2018 12:15 pm
Forum: General support questions
Topic: DL1 Serial Refresh Rates
Replies: 2
Views: 6848

Re: DL1 Serial Refresh Rates

Hi, I did a bit of playing around with a variable frequency square wave and as you say the refresh rate massively increases once there is new data to display, it seems the DL1 is cleverer than we thought :D Regards RPM, yes, of course, there is no way for it to output a frequency of zero. If I'd had...
by Turbo Synthesis
Tue Mar 06, 2018 2:09 pm
Forum: General support questions
Topic: DL1 Serial Refresh Rates
Replies: 2
Views: 6848

DL1 Serial Refresh Rates

Hi, We have a DL1 logger hooked up to our own analysis software via the serial port at 115200 BAUD Its taken a while to decode the serial stream but that's all up and working now, no real issues there, however we don't seem to be getting anywhere near the refresh rates that are set up in the logger....

Go to advanced search