The pinout will not have changed on the units since that time.
The unit can be configured to use the GPS speed as the vehicle speed.
Search found 263 matches
- Mon Apr 16, 2018 8:26 am
- Forum: General support questions
- Topic: 2015 Dash 2 Pro Pin Out
- Replies: 2
- Views: 6792
- Mon Apr 16, 2018 8:14 am
- Forum: Sensor-related questions
- Topic: Standard Analog Sensor issues
- Replies: 6
- Views: 38207
Re: Standard Analog Sensor issues
I would start by checking the wiring on the sensors. If you have a multimeter check that you have 5v on the sensor supply wire and check that the ground wire is connected correctly. Measure the voltage on the sensor wire where it goes in to the display. For the tacho, check the setting for the numbe...
- Wed Apr 11, 2018 2:59 pm
- Forum: General support questions
- Topic: Dash2 - CAN interface question
- Replies: 3
- Views: 7860
Re: Dash2 - CAN interface question
The value going in on misc 4 is in m/s, not mph. As such you are feeding in a speed of 100m/s, which is 223mph. In your can adapter put a divider in of 2.23694.
- Tue Apr 10, 2018 11:35 am
- Forum: General support questions
- Topic: speed sensor setup
- Replies: 3
- Views: 7666
Re: speed sensor setup
can you please email the configuration this generates directly over to me, mhill at race-technology.com and I'll take a look for you.
- Thu Apr 05, 2018 8:02 am
- Forum: General support questions
- Topic: speed sensor setup
- Replies: 3
- Views: 7666
Re: speed sensor setup
Are you using the automatic tool to set up your gear ratios? What are you putting in for your wheel circumference? If you are getting the correct speed with your pulses per km set to a particular value then that is correct. Don't adjust that to get the gearing right. It is the gearing settings which...
- Tue Mar 20, 2018 9:29 am
- Forum: General software support
- Topic: Dash 2 / DL1 Sport Omex ECU Interface
- Replies: 4
- Views: 13430
Re: Dash 2 / DL1 Sport Omex ECU Interface
I honestly don't know on that as I have never used that software. Given that there are two options I would try with one on, if it doesn't work try with the other.
- Mon Mar 19, 2018 9:55 am
- Forum: General software support
- Topic: Dash 2 / DL1 Sport Omex ECU Interface
- Replies: 4
- Views: 13430
Re: Dash 2 / DL1 Sport Omex ECU Interface
On the DL1 SPORT the only configuration required is to tick the box to say that the RPM data should be taken from the ECU interface. If that is ticked then I suggest checking the RS232 data output from the DL1 using the Live Monitor so you can see exactly what is being transmitted.
- Fri Mar 16, 2018 1:50 pm
- Forum: General support questions
- Topic: Syvecs S6GP Data
- Replies: 10
- Views: 20312
Re: Syvecs S6GP Data
You can add them in multiples of 15 channels, up to a maximum of 75.
- Wed Mar 07, 2018 10:19 am
- Forum: General support questions
- Topic: DL1 Serial Refresh Rates
- Replies: 2
- Views: 7040
Re: DL1 Serial Refresh Rates
Hi, The update rates are the maximum that you will see. They output at a default low background rate but otherwise only transmit up to the maximum rate if there is new data to display. So if you connect a sine wave generator to an analogue input you should see the output at the required rate, but if...
- Tue Mar 06, 2018 12:39 pm
- Forum: General support questions
- Topic: See all the best turns on the display
- Replies: 6
- Views: 9894
Re: See all the best turns on the display
Yes, that is correct.
- Tue Mar 06, 2018 10:31 am
- Forum: Installation questions
- Topic: DL1 Club - DASH4 PRO - ECU - Configure etc
- Replies: 2
- Views: 30376
Re: DL1 Club - DASH4 PRO - ECU - Configure etc
If the data logger is showing a card error with the card inserted I would try connecting without the card in. With power applied to the data logger plug the USB in and then when the port appears in the drop down list in the DL1 configuration software try to read back the configuration. If the data l...
- Mon Mar 05, 2018 1:59 pm
- Forum: General support questions
- Topic: See all the best turns on the display
- Replies: 6
- Views: 9894
Re: See all the best turns on the display
You can view them live on the display of the DASH2, but you can't go back over the results at the end of the session and review them. It only stores information internally on the number of laps and the time details from the best lap. It doesn't store all lap timing data.
- Mon Mar 05, 2018 12:02 pm
- Forum: General support questions
- Topic: Syvecs S6GP Data
- Replies: 10
- Views: 20312
Re: Syvecs S6GP Data
Hi Matt
This may be possible, but the external interface is limited to 15 channels so if we can do this we would only be able to add one more channel.
If you would like us to look in to this for you, please could you email support@race-technology.com and we will see if we are able to help.
This may be possible, but the external interface is limited to 15 channels so if we can do this we would only be able to add one more channel.
If you would like us to look in to this for you, please could you email support@race-technology.com and we will see if we are able to help.
- Mon Mar 05, 2018 11:00 am
- Forum: General support questions
- Topic: See all the best turns on the display
- Replies: 6
- Views: 9894
Re: See all the best turns on the display
If you set up the lap marker file on the DL1 with sector markers then you will be able to see your sector times on the DASH2. You can set up the lap files in the Analysis software and then save them on to the DL1 memory card.
- Mon Mar 05, 2018 10:50 am
- Forum: General software support
- Topic: PROBLEMS CONFIGURING DASH2 TO CAN MBE 9A4
- Replies: 2
- Views: 11260
Re: PROBLEMS CONFIGURING DASH2 TO CAN MBE 9A4
Hi Karl
We have received your emails, thank you.
Somebody from our technical support team will be in touch to assist you as soon as they can.
Best regards,
Adele
We have received your emails, thank you.
Somebody from our technical support team will be in touch to assist you as soon as they can.
Best regards,
Adele