Search found 82 matches
- Tue Sep 24, 2013 5:37 pm
- Forum: General support questions
- Topic: possible to set up a warning light?
- Replies: 13
- Views: 18468
Wow, firmware update for Dash3? That'd be very cool, would like to keep appraised... That said... I originally set mine up to do similar... but I've found it to be a bit less useful than expected. My primary problem is that the LCD screen of the Dash3 is too hard to read in an open-top car (sports p...
- Tue Sep 10, 2013 6:07 pm
- Forum: Sensor-related questions
- Topic: Resistance temp sender equation/formula
- Replies: 4
- Views: 9357
Not sure about the Autometer temp sender, but the VDO senders I'm using are exponential/logarithmic in their output (per the mfgr). Same wiring setup, I suspect, with 1000Ohm resistor. When I tried to use the Analysis SW to create a mapping, the accuracy was very poor, since it was only trying to do...
- Tue Sep 03, 2013 11:56 am
- Forum: General support questions
- Topic: Pot values for suspension measurement
- Replies: 3
- Views: 13016
- Wed Aug 28, 2013 11:59 am
- Forum: General support questions
- Topic: Pot values for suspension measurement
- Replies: 3
- Views: 13016
I'm doing this; I'm using Ford TPS sensors (eg, 5.0L V8 application) on my rear bellcranks. Since those are certainly less than 90 deg total movement, it works fine. I did have one crap out and give untrustworthy readings, but the other was good; I've swapped out the former and will retry. Haven't d...
- Fri Aug 23, 2013 12:13 pm
- Forum: General support questions
- Topic: Lap times Dash4Pro
- Replies: 8
- Views: 27911
- Wed Aug 21, 2013 11:59 am
- Forum: General support questions
- Topic: Lap times Dash4Pro
- Replies: 8
- Views: 27911
- Tue Aug 20, 2013 2:09 pm
- Forum: General support questions
- Topic: Lap times Dash4Pro
- Replies: 8
- Views: 27911
- Tue Aug 20, 2013 12:00 pm
- Forum: General support questions
- Topic: DL1 recording for only 60 secs or less
- Replies: 5
- Views: 8623
I've never seen any problems with the car moving in the slot... and my racecar is a step or two beyond a Radical (with respect to speed and harshness in-cockpit)... It is conceivable that you might have a ground or power wire that wiggles loose at speed though. I assume this isn't a problem you can ...
- Mon Aug 19, 2013 12:24 pm
- Forum: General support questions
- Topic: DL1 recording for only 60 secs or less
- Replies: 5
- Views: 8623
- Mon Aug 19, 2013 12:23 pm
- Forum: General support questions
- Topic: Lap times Dash4Pro
- Replies: 8
- Views: 27911
Sounds correct/normal. The lap or sector time screen will be displayed for a specified time after passing that gate; usually it's not that long of a time, say 3-5s by default IIRC. You can increase the display time... but if you have a lot of sectors, you'll just keep getting new ones over top of th...
- Tue Jul 09, 2013 12:47 pm
- Forum: General support questions
- Topic: Most of the time no data logged on CF.
- Replies: 5
- Views: 9767
- Tue Jun 25, 2013 12:06 pm
- Forum: Sensor-related questions
- Topic: Boost sensor queries
- Replies: 4
- Views: 9864
Suggestion - have you checked the cal on the sensor? You should be able to use a mighty-vac, with some creative matching of fittings etc, to apply at least that much pressure/vacuum... At least to get a sanity check, which seems to be what you're after. Are you logging CAN signals from the ECU as we...
- Mon Jun 24, 2013 1:39 pm
- Forum: General support questions
- Topic: CBR 1000RR
- Replies: 8
- Views: 11435
- Fri Jun 21, 2013 4:13 pm
- Forum: General support questions
- Topic: CBR 1000RR
- Replies: 8
- Views: 11435
- Mon Jun 17, 2013 12:42 pm
- Forum: General software support
- Topic: Dash3 config - show bitmap with channel??
- Replies: 3
- Views: 8014
OK, have investigated the display screens function... looks like it could be quite useful, especially as I don't actually use all 4 screens much. Unfortunately, there is still the apparent limitation in the software that only one variable can be used to toggle display screens... for example, I can't...