Search found 326 matches
- Thu Mar 02, 2006 9:48 pm
- Forum: General software support
- Topic: Circuit Overlays
- Replies: 11
- Views: 22314
As has been mentioned, the problem is the accuracy of the basic GPS unit, it can drift around by a few metres, this drift can take a long time, so from one lap to the next the accuracy will look very good, but if you overlay sessions from different days you can easily get an offset. This is exactly ...
- Thu Mar 02, 2006 9:37 pm
- Forum: Sensor-related questions
- Topic: DL1 and RPM
- Replies: 6
- Views: 16156
If you connect directly to the coil you need to connect to the negative side, the side which is switched by the ignition system. If you have connected to the red wire this could well be the 12v side which is just a permanent 12v while the ignition is turned on. I would try connecting to one of the o...
- Thu Feb 02, 2006 5:33 pm
- Forum: Sensor-related questions
- Topic: Sensor prices
- Replies: 20
- Views: 42844
From looking at the pictures of the sensors, they are not all of the same quality, you are not comparing like with like. If you wish to use those sensors with your DL1 then go ahead, there will be no problem at all so long as you can get the calibration information. Our system has been designed to b...
- Thu Feb 02, 2006 5:00 pm
- Forum: General support questions
- Topic: Downloading HEX files
- Replies: 9
- Views: 19595
- Mon Nov 28, 2005 4:35 pm
- Forum: General software support
- Topic: G-circle
- Replies: 3
- Views: 9699
- Mon Nov 28, 2005 11:39 am
- Forum: Installation questions
- Topic: DL-90 installation manual
- Replies: 2
- Views: 10835
Hi, All the manuals with regard to installation of hardware are now included in the main help within the Analysis software. If you start up the software and run the help you should see a section on Hardware, within this are product specific sections which then cover the installation and operation of...
- Mon Nov 28, 2005 11:37 am
- Forum: Installation questions
- Topic: Location of GPS sensor for DL1
- Replies: 3
- Views: 11325
Hi, The plastic could affect the signal, it really depends on exactly what the plastic is made of, the only real way to find out is to try it and see how you get on. Ideally the antenna would be mounted as high up as possible with a clear view to the horizon in all directions. To see how good the si...
- Mon Nov 28, 2005 11:31 am
- Forum: General software support
- Topic: Show Selected Variables
- Replies: 1
- Views: 7360
Hi, The values table which show all variables which are currently selected. If you are using V6, go to the variable explorer, tick the box next to each variable you wish to view and then click the Apply button. All selected variables will then be visible when you click on a point on the graph or tra...
- Mon Nov 28, 2005 11:26 am
- Forum: General software support
- Topic: Produce a Graph Showing Velocity
- Replies: 1
- Views: 7259
Hi, The easiest way to do this is to download the new V6 software, If you then go into the variable explorer you will see that you have the ability to integrate or differentiate the variable with respect to time or distance. If you set up a user defined variable to be the differential of shock posit...
- Fri Nov 25, 2005 1:53 pm
- Forum: General support questions
- Topic: Monitor sw not working
- Replies: 4
- Views: 12720
Hi Henrik, You can test it with hyperterminal, set it to 115200 baud, 8 data bits, 1 stop bit, no parity, no flow control. With the DL1 connected to it you should see a copyright message when the DL1 is first turned on. Make sure that you are using the null modem cable supplied with your DL1, you ca...
- Fri Nov 25, 2005 9:36 am
- Forum: General support questions
- Topic: Firmware DL1 V6 contents
- Replies: 1
- Views: 7914
You can just ignore that line, it tells me which version of the code it is. The DL1 and DL2 firmware now contains some modes to aid communication over a GSM interface. This mode must be disabled if the DL1 is used with a serial input stream, such as from an ECU or an IMU06. The GSM mode is enabled w...