Search found 71 matches
- Wed Apr 22, 2020 3:08 pm
- Forum: General software support
- Topic: Racetech 2 Speed Dropping out at 55mph
- Replies: 4
- Views: 8967
Re: Racetech 2 Speed Dropping out at 55mph
Get a scope and check the frequency of the hall effect output.
- Mon Apr 20, 2020 5:39 pm
- Forum: General software support
- Topic: Racetech 2 Speed Dropping out at 55mph
- Replies: 4
- Views: 8967
Re: Racetech 2 Speed Dropping out at 55mph
I had a similar issue on my Noble.
Solution was to reduce number of rotating teeth on axle from 10 to 4. Basically frequency count became too high at 50mph ish.
Solution was to reduce number of rotating teeth on axle from 10 to 4. Basically frequency count became too high at 50mph ish.
- Mon Mar 30, 2020 8:06 pm
- Forum: Sensor-related questions
- Topic: oil pressure sensor checks
- Replies: 5
- Views: 32612
Re: oil pressure sensor checks
Do you have a Mityvac or similar tool that can produce a known variable pressure?
- Tue Mar 24, 2020 10:40 pm
- Forum: General software support
- Topic: DL1 MK2 - latest available firmware
- Replies: 1
- Views: 6460
Re: DL1 MK2 - latest available firmware
AFAIK all the latest device updates are in the software package.
- Fri Mar 06, 2020 7:07 pm
- Forum: General support questions
- Topic: Dash2 and windows10 *pulling my hair out*
- Replies: 5
- Views: 10216
Re: Dash2 and windows10 *pulling my hair out*
Which, for the benefit of others who encounter same problem, was?the email advice..
- Thu Oct 03, 2019 4:55 pm
- Forum: General software support
- Topic: Dash 2 on Yamaha R1 1999 HELP!
- Replies: 1
- Views: 6225
Re: Dash 2 on Yamaha R1 1999 HELP!
Give us some clues..
Which sensors?
Sensor characteristics - one wire? two wire? Sensor output - variable resistance? variable voltage?
Which sensors?
Sensor characteristics - one wire? two wire? Sensor output - variable resistance? variable voltage?
- Tue May 21, 2019 7:40 am
- Forum: General software support
- Topic: odometer setup
- Replies: 3
- Views: 8423
Re: odometer setup
Email RT. IIRC they can do that for you. A charge may be payable.
- Tue Apr 30, 2019 5:45 pm
- Forum: General software support
- Topic: DASH2 move from DAT to CMG
- Replies: 4
- Views: 9348
Re: DASH2 move from DAT to CMG
Huh? What's the big deal? I've done 3 so far. Each one less than 40 minutes. New software so much easier to use.
But then i had all the settings in a spreadsheet.
IIRC, took me 5 hours to upgrade my last Windose PC...
But then i had all the settings in a spreadsheet.
IIRC, took me 5 hours to upgrade my last Windose PC...
- Fri Apr 26, 2019 9:39 pm
- Forum: General software support
- Topic: DASH2 move from DAT to CMG
- Replies: 4
- Views: 9348
Re: DASH2 move from DAT to CMG
AFAIK, when you upgrade to latest firmware, you start off with a blank sheet and have to rebuild your config from scratch, channel by channel, sensor by sensor.
- Thu Oct 04, 2018 10:30 pm
- Forum: General support questions
- Topic: Upload Calibration & Lost ECU CAN Interface Data
- Replies: 4
- Views: 11083
Re: Upload Calibration Lost ECU CAN Interface Data
Few too many Bud Lights?Well after a second look it looks like the TWIN 350 emblems are obsolete as well. Double suck… Are there any custom graphics makers out there that you can email a picture to and have them make you something similar?
- Sun Sep 16, 2018 4:36 pm
- Forum: General support questions
- Topic: Revs higher than 9000rpm and fuel sending question - motorbike related
- Replies: 5
- Views: 11166
Re: Revs higher than 9000rpm and fuel sending question - motorbike related
You can't. AFAIK you need to send the unit to RT for them to do for you.I couldn't see on the software about programming in the odometer reading so that it can continue from where my analogue instrument cluster leaves off.
- Sun Sep 09, 2018 9:19 pm
- Forum: General support questions
- Topic: Need to update settings on Dash2 v9.3.4
- Replies: 7
- Views: 11749
Re: Need to update settings on Dash2 v9.3.4
Send me an email to noblem500 AT gmail.com and i'll send you a copy of the manual.
- Sun Sep 09, 2018 10:02 am
- Forum: General support questions
- Topic: Need to update settings on Dash2 v9.3.4
- Replies: 7
- Views: 11749
Re: Need to update settings on Dash2 v9.3.4
Have you tried reading the manual?
The tasks you're wanting to do are normal for anyone setting a Dash2 up and are pretty simple if you follow the manual.
The tasks you're wanting to do are normal for anyone setting a Dash2 up and are pretty simple if you follow the manual.
- Thu Aug 09, 2018 6:30 pm
- Forum: General software support
- Topic: Dash 2 sensors set up
- Replies: 4
- Views: 21661
Re: Dash 2 sensors set up
Have you got the temperature/resistance curve for the sensor?
If not, stick it in ice and boiling water and measure resistance. Do same in a saucepan for 2 or 3 more temperatures, say at 20 40 and 60 degrees.
Then input the data in the sensor configuration. Job done.
If not, stick it in ice and boiling water and measure resistance. Do same in a saucepan for 2 or 3 more temperatures, say at 20 40 and 60 degrees.
Then input the data in the sensor configuration. Job done.
- Tue Jul 31, 2018 11:56 pm
- Forum: General software support
- Topic: Dash2 Set up Help in york
- Replies: 2
- Views: 10927
Re: Dash2 Set up Help in york
Hi Jim
I'm in Barnsley and can easily pop up to you.
Send me an email to noblem500 AT gmail.com (replace the AT and delete the spaces) with a phone number and i'll give you a call.
Peter
I'm in Barnsley and can easily pop up to you.
Send me an email to noblem500 AT gmail.com (replace the AT and delete the spaces) with a phone number and i'll give you a call.
Peter