Search found 263 matches

by racetec
Tue Oct 29, 2019 12:39 pm
Forum: General software support
Topic: Analysis Software - Multiple Vehicles
Replies: 4
Views: 10872

Re: Analysis Software - Multiple Vehicles

The short answer is that on the older DL1 MK2 it was a "pain" as the sensor in volts->units conversion was done on the PC, so you had to keeping loading in different variable files. I don't think you are missing anything here. On later DL1s (MK3 onwards, sold from about 2008) the conversion from vol...
by racetec
Tue Oct 29, 2019 11:08 am
Forum: GoPro standalone software
Topic: GoPro Standalone Software Support
Replies: 39
Views: 156067

Re: GoPro Standalone Software Support

Hi Stan

Glad to hear the issue has been resolved! :)
by racetec
Thu Oct 24, 2019 8:24 am
Forum: GoPro standalone software
Topic: GoPro Standalone Software Support
Replies: 39
Views: 156067

Re: GoPro Standalone Software Support

Hi Stan

Thanks for getting in touch. I understand that you are speaking with Andy directly on email and he is helping you resolve this issue.

Best regards,
Support (AH)
by racetec
Wed Oct 16, 2019 10:49 am
Forum: Installation questions
Topic: Omex 710 Tacho output
Replies: 2
Views: 27148

Re: Omex 710 Tacho output

Hello

The tachometer output from an ECU is to be connected directly to the low level RPM input (for any RT product).

The wiring diagrams for the DASH2 can be found here:
https://www.race-technology.com/wiki/in ... stallation
by racetec
Thu Oct 10, 2019 12:30 pm
Forum: General software support
Topic: Dash4 Pro - Post session review
Replies: 2
Views: 8282

Re: Dash4 Pro - Post session review

Hi Stuart

This is in Menu 1.1 : Quick Session Review - shows a summary for each lap.

Support (AH)
by racetec
Thu Sep 05, 2019 10:17 am
Forum: General software support
Topic: Dash2 hooked up with DL1 MK2
Replies: 1
Views: 6718

Re: Dash2 hooked up with DL1 MK2

Hello Frederik Please see below page for a diagram of how to connect your DL1, DASH2 and ECU Interface: https://www.race-technology.com/wiki/index.php/ConnectingHardware/DLx-ECU-DASHx The page also has a link to some information regarding configuring the DL1 to work with the dash. I hope this helps....
by racetec
Tue Sep 03, 2019 10:33 am
Forum: General software support
Topic: Motorbike 1 wire water temp connector installation advice
Replies: 1
Views: 6632

Re: Motorbike 1 wire water temp connector installation advice

Hello

Yes, to use that sensor you will need a pullup resistor and this should be around 270-300 Ohms.
A little bit more would be ok but definitely not less.

Best regards,
Support (AH)
by racetec
Wed Aug 14, 2019 8:19 am
Forum: GoPro standalone software
Topic: GoPro Standalone Software Support
Replies: 39
Views: 156067

Re: GoPro Standalone Software Support

Hi Stan

Thanks for sending over your files - these have been forwarded to the software team.

Support (AH)
by racetec
Mon Aug 12, 2019 3:38 pm
Forum: GoPro standalone software
Topic: GoPro Standalone Software Support
Replies: 39
Views: 156067

Re: GoPro Standalone Software Support

Thanks for sharing these, Stan!
by racetec
Fri Aug 09, 2019 1:23 pm
Forum: General software support
Topic: Speed not regitering
Replies: 3
Views: 8371

Re: Speed not regitering

There is no pull up resistor built in to the DASH2, so if you sensor does not drive the output high you will need a pullup resistor.

Martin
by racetec
Fri Aug 09, 2019 11:22 am
Forum: General software support
Topic: Speed not regitering
Replies: 3
Views: 8371

Re: Speed not regitering

If you have a multimeter I would check the output from the sensor with a voltmeter to ensure that the trigger output is changing state.

Martin
by racetec
Wed Aug 07, 2019 11:27 am
Forum: General software support
Topic: Set up help required with DL1/Dash 2 in Hereford
Replies: 2
Views: 10417

Re: Set up help required with DL1/Dash 2 in Hereford

Do you have a logged data file from the DL1? If you want to send a data file and your configuration files over to me I'll take a look at them for you. mhill at race-technology.com

Martin
by racetec
Fri Aug 02, 2019 1:05 pm
Forum: General software support
Topic: Dl1 firmware
Replies: 2
Views: 7760

Re: Dl1 firmware

Do you know which firmware you are running at the moment? The latest DL1 MK2 firmware is V43 from May 2011.

Martin
by racetec
Thu Aug 01, 2019 8:07 am
Forum: General software support
Topic: DL1 Mk2 has power but wont turn on...
Replies: 3
Views: 8895

Re: DL1 Mk2 has power but wont turn on...

Hello You could check if the compact flash card housing pins have been pushed through the back and are touching each other. If not, it sounds like the unit will need to be returned to RT for repairs, although due to the age of the unit this may not be possible. We are currently offering 30% off a ne...
by racetec
Wed Jul 17, 2019 3:41 pm
Forum: GoPro standalone software
Topic: GoPro Standalone Software Support
Replies: 39
Views: 156067

GoPro Standalone Software Support

Hello! Our new V10 software package includes a "Standalone GoPro" Mode allowing users to use GoPro video and its embedded GPS data for comprehensive race analysis without using any Race Technology hardware. More information can be found on our website, here: http://www.race-technology.com/gb/racing/...

Go to advanced search