Please help with errors.
"1. GPS rates are set to >10Hz and internal GPS only runs at a maximum of 10Hz"
GPS 20 Hz data enebled in serial and storage.
My DL1 MK3 was ordered and delivered with 20Hz GPS and a (wrong?) codes.bin.
Do I need a licence.dat?
"2. Same data source has been selected for CAN RAW data ports 5 and 1"
CAN data input is in Silent mode, Output CAN data is disabled.
"3. 1 kHz logging enabled for data storage but not enabled in device"
??????
"4. Extended frequency channels enabled for output or storage but not enabled in device"
I use only in Frequency inputs> Frequency[Hz]
"5. CAN port 2 output channels enabled but not enabled in device"
CAN data input is in Silent mode, Output CAN data is disabled.
Andre
DL1 MK3 Errors
DL1 MK3 Errors
DL1-MK3+20HzGPS, DASH3
Support
Hello,
These warning messages should be seen as just guidance rather then errors.
These messages are currently being reviewed and our next release of software will have any bugs fixed.
1. The DL1 mk3 can only log its own GPS data at a maximum of 5Hz except the raw data which is logs at 20Hz. The 20Hz GPS data isn't a processed solution and the DL1 only records the RAW satellite data. Once you load this data in to the PC the software reprocesses the RAW data and gives 20Hz speed and position data. The reason the option is there to log faster the 5Hz is because it is possible to set the GPS data to come from the serial port and not the built in port. Our professional speedbox range offers 20Hz processed speed and position data.
2. This is advising the data source in memory card of serial port configuration software for CAN RAW data is the same. (ignore this it will be changed) The CAN silent mode is guidance as it is just a note to remind you about CAN silent mode because this feature often is the cause to getting no data for no obvious reason.
3. This is trying to say you do not have a license for the configured logging rates. DL1 has default maximum of 100Hz. This is a bug and a hidden message is selected to 1000Hz.
4. This is advising you that some messages are configured to be stored on the memory card or be transmitted out of the serial port are not enabled. The DL1 by default can only measure frequency the extended license enable to log high and low time. In the variable mapping select the extended frequency input channels to come from serial port and the message will go away.
5. Some hidden messages are enabled on CAN port 2. This will be fixed on the next version.
Kind regards,
Kieran
Support
These warning messages should be seen as just guidance rather then errors.
These messages are currently being reviewed and our next release of software will have any bugs fixed.
1. The DL1 mk3 can only log its own GPS data at a maximum of 5Hz except the raw data which is logs at 20Hz. The 20Hz GPS data isn't a processed solution and the DL1 only records the RAW satellite data. Once you load this data in to the PC the software reprocesses the RAW data and gives 20Hz speed and position data. The reason the option is there to log faster the 5Hz is because it is possible to set the GPS data to come from the serial port and not the built in port. Our professional speedbox range offers 20Hz processed speed and position data.
2. This is advising the data source in memory card of serial port configuration software for CAN RAW data is the same. (ignore this it will be changed) The CAN silent mode is guidance as it is just a note to remind you about CAN silent mode because this feature often is the cause to getting no data for no obvious reason.
3. This is trying to say you do not have a license for the configured logging rates. DL1 has default maximum of 100Hz. This is a bug and a hidden message is selected to 1000Hz.
4. This is advising you that some messages are configured to be stored on the memory card or be transmitted out of the serial port are not enabled. The DL1 by default can only measure frequency the extended license enable to log high and low time. In the variable mapping select the extended frequency input channels to come from serial port and the message will go away.
5. Some hidden messages are enabled on CAN port 2. This will be fixed on the next version.
Kind regards,
Kieran
Support
______________________________
Posted by Race Technology Support
Posted by Race Technology Support
Return to “General support questions”
Who is online
Users browsing this forum: No registered users and 36 guests
