I only get value of 1 in gear selection value. I have entered all gear ratios, final drive and wheel circumference and have no results over 20 odd runs. What have I missed.
thanks
Vince
Gear selection wont register
Hi,
Resurrecting this old topic. I searched through the whole forum and found a few topics on this. Still couldn't resolve this issue.
I have DL1 + Dash2 (Analysis software ver 7, if that helps)
RPM to DASH2 (works fine, no spikes, setup correctly)
GPS Speed from DL1 and looks to be correct
SPEEDOMETER YES via RS232
Gear ratios set via DASH2 config software, then downloaded to DASH2
ANA GEAR ON (forgot the exact wording on the DASH2 setup screen)
Most of the times the indicator shows I'm in R. But sometimes I see some flicker of a number there.
What am I not doing or doing wrong?
Thanks!
Resurrecting this old topic. I searched through the whole forum and found a few topics on this. Still couldn't resolve this issue.
I have DL1 + Dash2 (Analysis software ver 7, if that helps)
RPM to DASH2 (works fine, no spikes, setup correctly)
GPS Speed from DL1 and looks to be correct
SPEEDOMETER YES via RS232
Gear ratios set via DASH2 config software, then downloaded to DASH2
ANA GEAR ON (forgot the exact wording on the DASH2 setup screen)
Most of the times the indicator shows I'm in R. But sometimes I see some flicker of a number there.
What am I not doing or doing wrong?
Thanks!
-
- Posts: 220
- Joined: Thu Mar 15, 2007 3:41 pm
- Location: Norwich, UK
- Contact:
What gear ratio data are you actually using?
Can you type here exactly what you write in the config software? Gear ratios should be other type where 1st ~= 3.5, and not 0.28.
Same for final drive (your number will be around 3, not 0.something).
Wheel circumference will be in the region of 1.9m
Any major differences to this will cause problems. Probably. Maybe.
Can you type here exactly what you write in the config software? Gear ratios should be other type where 1st ~= 3.5, and not 0.28.
Same for final drive (your number will be around 3, not 0.something).
Wheel circumference will be in the region of 1.9m
Any major differences to this will cause problems. Probably. Maybe.
Monoposto 2000 - Reynard 883 Toyota
I fixed the problem. It was a user error. I even described the error in my first post. ANA GEAR should be OFF. I think that's for analog signal via the pot installed in certain gearboxes.
Next problem:
When I'm in 5th, Dash2 sometimes flickers between 5 and 4. Is this due to inaccurate tire circumference value (estimate vs. actual, i.e. I got circumference from tire size calculation, not actual measurement). But why does it only happen in 5th gear?
Also what should one enter in the gear 6 and 7 if one doesn't have them?
Thank you.
Next problem:
When I'm in 5th, Dash2 sometimes flickers between 5 and 4. Is this due to inaccurate tire circumference value (estimate vs. actual, i.e. I got circumference from tire size calculation, not actual measurement). But why does it only happen in 5th gear?
Also what should one enter in the gear 6 and 7 if one doesn't have them?
Thank you.
If you had a problem with the tire size it would show up in 4/5 gear because these ratios are closer to each other than any other pair of gears. When I was doing my initial analysis of gear #, I found that my calculated tire diameter was about 5% larger than the empirical value I got when looking at the actual data.
To get a good estimated tire diameter, I created a user variable for the speed in each gear and compared this trace to the GPS speed trace. I would adjust the tire diameter until I got a very close match between these traces.
As a note, I put the ratios and tire diameter into car constants to simplify the speed in gear calculations.
Paul
To get a good estimated tire diameter, I created a user variable for the speed in each gear and compared this trace to the GPS speed trace. I would adjust the tire diameter until I got a very close match between these traces.
As a note, I put the ratios and tire diameter into car constants to simplify the speed in gear calculations.
Paul
-
- Posts: 20
- Joined: Tue Dec 16, 2008 12:28 pm
- Location: Darlington
westysprinter wrote:mine is fine until 5th when it just goes back to a - sign!
See my post here:
http://www.race-technology.com/forum/viewtopic.php?p=5622#5622
Fraser E White
as you can see from the adjacent post, I am having very similar problems .. is your's a bike or car engine? I have no idea if the extremely high revs is causing a problem but clearly it has worked (see post from Fraser) in car application ... not found anyone yet who has cracked it for a bike engine revving at 8-11000 all the time.
Return to “General support questions”
Who is online
Users browsing this forum: No registered users and 252 guests