Pulling my hair out over this one and I suspect it's something simple.
Just wired the analogue channels into the brand new dash 2, oil and fuel and they work ok but the dash won't read anything coming from the omex600
In map4000 I've set up the serial channel exactly as per the knowledge base, the only input I don't have is lambda 2 but I've just selected something else for that.
Then on the dash 2 I've entered the ECU interface and selected the ones I want
But the values do not show on the screen, they are just zeros
I can't find anything else in the map4000 software to enable anything and I'm stuck. I haven't changed any of the ECU wiring and I'm simply using the aerial adapter thing that was sent with the dash
Any ideas folks?
Dash 2 to omex 600 problem
Re: Dash 2 to omex 600 problem
Hello,
The ECU setup should look more like this...
![Image](http://i67.tinypic.com/ayz2q.jpg)
I can email you the ECU setup file. Please send me an email and i will reply Kieran @ race - technology . com
Kind regards,
Support
The ECU setup should look more like this...
![Image](http://i67.tinypic.com/ayz2q.jpg)
I can email you the ECU setup file. Please send me an email and i will reply Kieran @ race - technology . com
Kind regards,
Support
______________________________
Posted by Race Technology Support
Posted by Race Technology Support
Re: Dash 2 to omex 600 problem
Yes, looks exactly like that other than the second lambda 1 is just a random one that I used . The RT document states I should use lambda 2 which doesn't exist in the Omex
My email address is tony.birkbeck@btconnect.com , does the set up file change anything other than this screen?
My email address is tony.birkbeck@btconnect.com , does the set up file change anything other than this screen?
Re: Dash 2 to omex 600 problem
Hello,
I will email you the setup file anyway but I believe it doesn't do anything else.
1) Please can you connect the interface like this...
![Image](http://i64.tinypic.com/k06mhw.jpg)
2) Open live monitor
![Image](http://i64.tinypic.com/fa7znc.jpg)
3) Connect to port connected to interface
![Image](http://i67.tinypic.com/2rq2gpz.jpg)
4) Switch on the power to the interface and ECU
Do you see any data?
![Image](http://i63.tinypic.com/dr2xc.png)
If no, do you see any OK or error samples counting up?
![Image](http://i65.tinypic.com/2l887a.jpg)
Kind regards,
Support (K)
I will email you the setup file anyway but I believe it doesn't do anything else.
1) Please can you connect the interface like this...
![Image](http://i64.tinypic.com/k06mhw.jpg)
2) Open live monitor
![Image](http://i64.tinypic.com/fa7znc.jpg)
3) Connect to port connected to interface
![Image](http://i67.tinypic.com/2rq2gpz.jpg)
4) Switch on the power to the interface and ECU
Do you see any data?
![Image](http://i63.tinypic.com/dr2xc.png)
If no, do you see any OK or error samples counting up?
![Image](http://i65.tinypic.com/2l887a.jpg)
Kind regards,
Support (K)
______________________________
Posted by Race Technology Support
Posted by Race Technology Support
Re: Dash 2 to omex 600 problem
ok, ill try and get to this as soon as possible - the car is some distance away from me so it might need to be this weekend -ill report back asap ![Very Happy :D](./images/smilies/icon_biggrin.gif)
ps - I haven't received an email ??
![Very Happy :D](./images/smilies/icon_biggrin.gif)
ps - I haven't received an email ??
Re: Dash 2 to omex 600 problem
Hi
right connected as per above but we cannot see any data and we have errors, the OK error rate is increasing all the time, note also that live monitor is a slightly different version?
what does this mean??
right connected as per above but we cannot see any data and we have errors, the OK error rate is increasing all the time, note also that live monitor is a slightly different version?
what does this mean??
![Cool 8)](./images/smilies/icon_cool.gif)
Re: Dash 2 to omex 600 problem
hi - support, any idea what the next step is?? ![Very Happy :D](./images/smilies/icon_biggrin.gif)
![Very Happy :D](./images/smilies/icon_biggrin.gif)
Re: Dash 2 to omex 600 problem
Hi Tony,
The OK messages is confirmation the interface is alive.
- The live monitor sends out a message which is restransmitted back to live monitor from the interface.
THis confirms...
- Power is OK
- PC communications is OK
- Interface is OK on the transmit side
Now we need to check the ECU is outputting the data. Connect the live monitor directly to the ECU. Just to be clear rmeove the ECU interface and connect the serial port directly to the connector that was going to the ECU interface from the ECU.
1) The ECU outputs data at 38,400. Change the baud rate on the live monitor
![Image](http://i65.tinypic.com/33jk8jc.jpg)
2) Swtich on the ECU and the interface
3) You should now see errors counting up in live monitor, do you?
- Live monitor only displays Race Technology messages. If it receives messages that do not match our protocol it will count it as an error.
If no then please check connections and ECU setup.
If yes, please capture 1 minute of error using the live monitor and email me the created file and i will check the data is correct.
Kind rgeards,
Support (K)
The OK messages is confirmation the interface is alive.
- The live monitor sends out a message which is restransmitted back to live monitor from the interface.
THis confirms...
- Power is OK
- PC communications is OK
- Interface is OK on the transmit side
Now we need to check the ECU is outputting the data. Connect the live monitor directly to the ECU. Just to be clear rmeove the ECU interface and connect the serial port directly to the connector that was going to the ECU interface from the ECU.
1) The ECU outputs data at 38,400. Change the baud rate on the live monitor
![Image](http://i65.tinypic.com/33jk8jc.jpg)
2) Swtich on the ECU and the interface
3) You should now see errors counting up in live monitor, do you?
- Live monitor only displays Race Technology messages. If it receives messages that do not match our protocol it will count it as an error.
If no then please check connections and ECU setup.
If yes, please capture 1 minute of error using the live monitor and email me the created file and i will check the data is correct.
Kind rgeards,
Support (K)
______________________________
Posted by Race Technology Support
Posted by Race Technology Support
Re: Dash 2 to omex 600 problem
Thanks Keiran - will get back to you as soon as I can - in the mean time can you mail me the Omex 600 set up file to tony.birkbeck@btconnect.com please and ill ask Rob to load that as well so we know 100% we have that bit right too...
Re: Dash 2 to omex 600 problem
Hi keiran
Still not received the Omex file?
Ok, live monitor plugged directly into ECU and error count is rising all the time the ECU is switched on ( see pictures below). I can't see what you mean about recording 1 minutes worth of errors? How do you do that as far as I can see there are no options for me to start recording them in live monitor?
What is the next step?
Still not received the Omex file?
Ok, live monitor plugged directly into ECU and error count is rising all the time the ECU is switched on ( see pictures below). I can't see what you mean about recording 1 minutes worth of errors? How do you do that as far as I can see there are no options for me to start recording them in live monitor?
What is the next step?
![Very Happy :D](./images/smilies/icon_biggrin.gif)
Re: Dash 2 to omex 600 problem
And not sure if this screen helps
It's the raw data, the show text message screen is just blank
It's the raw data, the show text message screen is just blank
Re: Dash 2 to omex 600 problem
Hello,
The live monitor is receiving byte value FF constantly which is telling me the data being received from the ECU is not at the correct baud rate or live monitor was not set to 38400.
I have sent the setup file now (sorry) please try loading it is and double checking the baud rate in live monitor is set to 38400 and try again.
To capture the data please follow these steps...
1) Click 'Start logging input data to disc'
![Image](http://i68.tinypic.com/2yo4hzd.jpg)
2) Select log everything and click ok
![Image](http://i67.tinypic.com/102w1s7.jpg)
3) After 1 minute of logging when errors are counting up
![Image](http://i68.tinypic.com/2vwvbly.jpg)
4) You should now see a result in the results explorer. Right click and select open file location. Email me the .run file.
![Image](http://i64.tinypic.com/2w6xpib.jpg)
The live monitor is receiving byte value FF constantly which is telling me the data being received from the ECU is not at the correct baud rate or live monitor was not set to 38400.
I have sent the setup file now (sorry) please try loading it is and double checking the baud rate in live monitor is set to 38400 and try again.
To capture the data please follow these steps...
1) Click 'Start logging input data to disc'
![Image](http://i68.tinypic.com/2yo4hzd.jpg)
2) Select log everything and click ok
![Image](http://i67.tinypic.com/102w1s7.jpg)
3) After 1 minute of logging when errors are counting up
![Image](http://i68.tinypic.com/2vwvbly.jpg)
4) You should now see a result in the results explorer. Right click and select open file location. Email me the .run file.
![Image](http://i64.tinypic.com/2w6xpib.jpg)
______________________________
Posted by Race Technology Support
Posted by Race Technology Support
Re: Dash 2 to omex 600 problem
Thanks Keiran
I've now loaded the setup file you sent via map4000 and sent this configuration into the ECU, it didn't actually change anything.
The Omex is being a bit temperamental with connection to the pc, it seems to take ages before it actually connects, anyway the baud rate is at 38400
Live monitor connects much more easily, we connected at 38400 and now have the run file which I have emailed you
Note that the live monitor version that we are using is slightly different from your screen shot...
Looking forward to getting the next steps...![Very Happy :D](./images/smilies/icon_biggrin.gif)
I've now loaded the setup file you sent via map4000 and sent this configuration into the ECU, it didn't actually change anything.
The Omex is being a bit temperamental with connection to the pc, it seems to take ages before it actually connects, anyway the baud rate is at 38400
Live monitor connects much more easily, we connected at 38400 and now have the run file which I have emailed you
Note that the live monitor version that we are using is slightly different from your screen shot...
Looking forward to getting the next steps...
![Very Happy :D](./images/smilies/icon_biggrin.gif)
Re: Dash 2 to omex 600 problem
Data received.
The data is just FF's which means it is not outputting the data correctly.
![Image](http://i66.tinypic.com/n6ssw9.jpg)
If all these things are true then it is time to contact OMEX
1) The ECU excepted the configuration file and is showing baud rate 38400
2) The live monitor is configured to 38400
3) You are able to check the ECU is configured to 38400 using the same connection you are using to capture the data. (This confirms the commination is working)
4) The ECU is running firmware 0.70 or later
Please confirm and I will forward to OMEX for you.
Kind regards,
Support (K)
The data is just FF's which means it is not outputting the data correctly.
![Image](http://i66.tinypic.com/n6ssw9.jpg)
If all these things are true then it is time to contact OMEX
1) The ECU excepted the configuration file and is showing baud rate 38400
2) The live monitor is configured to 38400
3) You are able to check the ECU is configured to 38400 using the same connection you are using to capture the data. (This confirms the commination is working)
4) The ECU is running firmware 0.70 or later
Please confirm and I will forward to OMEX for you.
Kind regards,
Support (K)
______________________________
Posted by Race Technology Support
Posted by Race Technology Support
Re: Dash 2 to omex 600 problem
Hi keiran, the live monitor is definitely at 38400. The Omex is definitely set to 38400 in the telemetry serial set up - I'm not aware of any other settings in the Omex that change the baud rate??
The config file was accepted but didn't actually change anything I had previously done using the instructions on the knowledge base
Firmware is definitely ok
Are you contacting Omex or should we?
The config file was accepted but didn't actually change anything I had previously done using the instructions on the knowledge base
Firmware is definitely ok
Are you contacting Omex or should we?
Return to “General software support”
Who is online
Users browsing this forum: No registered users and 172 guests