Search found 103 matches

by Bikey
Thu Jun 14, 2018 2:47 pm
Forum: General support questions
Topic: Horsepower Calculation Q's
Replies: 0
Views: 1073

Horsepower Calculation Q's

Hi - I'm trying to determine/confirm that I have an engine air intake issue at higher speeds (>100mph) by using the HP tool in analysis. When I ask it to perform the power calc, the number (380hp) matches my dyno number. I also get this same number when accelerating out of turns. But, when I check H...
by Bikey
Fri Jun 08, 2018 5:59 pm
Forum: Installation problems
Topic: DASH2Pro Signal Manipulation
Replies: 3
Views: 519

Re: DASH2Pro Signal Manipulation

"high rpm" is if you are pulling the signal from the spark plug wires, "low rpm" is for a signal from the computer.
by Bikey
Fri Jun 08, 2018 5:58 pm
Forum: Installation problems
Topic: DASH2Pro Signal Manipulation
Replies: 3
Views: 519

Re: DASH2Pro Signal Manipulation

here are the settings
c5 rpm.jpg
c5 rpm.jpg (176.66 KiB) Viewed 503 times
by Bikey
Fri Jun 08, 2018 1:58 pm
Forum: Installation problems
Topic: DASH2Pro Signal Manipulation
Replies: 3
Views: 519

Re: DASH2Pro Signal Manipulation

The OEM signal works fine on a friend's D2Pro that I installed. I can send you the settings if you message me your info. The water temp signal, as you've discovered, is quite curious. You can add a dedicated temp sensor to the rear of the passenger side head to get full range readings and avoid that...
by Bikey
Mon May 07, 2018 1:25 pm
Forum: Sensor-related questions
Topic: Strain gauges on DL1
Replies: 5
Views: 761

Re: Strain gauges on DL1

I have no experience (or affiliation) with this - but it is something to consider: http://www.izzeracing.com/products/stra ... ifier.html
by Bikey
Wed Mar 28, 2018 8:19 pm
Forum: General support questions
Topic: Syvecs S6GP Data
Replies: 10
Views: 1395

Re: Syvecs S6GP Data

Ok, you can just pay for as many 15 channel CAN licenses that you need (that will take care of the DL1 hardware side). On the DL1 software side, you will need to set it up to receive the CAN data and then map the incoming CAN data to a DL1 channel. I've attached a screenshot that will get you going....
by Bikey
Tue Mar 27, 2018 8:19 pm
Forum: General support questions
Topic: Syvecs S6GP Data
Replies: 10
Views: 1395

Re: Syvecs S6GP Data

which version DL1 do you have (is it a Mk3 with a direct CAN input)?
by Bikey
Fri Mar 16, 2018 3:10 am
Forum: General support questions
Topic: Syvecs S6GP Data
Replies: 10
Views: 1395

Re: Syvecs S6GP Data

A current DL1 that has a CAN bus input is able to receive any and all info sent by the S6 via CAN, correct (assuming enough of the 15 CAN channel licenses are purchased)? The 15 channel limitation is only with the CAN to serial interface, right?
by Bikey
Mon Jun 13, 2016 3:36 pm
Forum: How do I...
Topic: Getting simulation to work effectively with a Caterham
Replies: 1
Views: 3118

Re: Getting simulation to work effectively with a Caterham

I am interested as well, I have had the same issue with simulation times being unreasonably quick.
by Bikey
Fri May 27, 2016 1:20 pm
Forum: How do I...
Topic: Analysis v8.5.369
Replies: 4
Views: 4047

Re: Analysis v8.5.369

up, would really like to have the tabs back.

Thanks.
by Bikey
Fri May 27, 2016 1:19 pm
Forum: Requested new features
Topic: Math Channels
Replies: 1
Views: 4338

Re: Math Channels

Yes - there are 25 user defined variables available in the variable manager - and you can treat them as math channels (performing math operations on any input/combination of inputs).
I would appreciate if they could bump this number to at least 50.
by Bikey
Fri May 06, 2016 5:13 pm
Forum: General support questions
Topic: Displaying Gear from ECU
Replies: 4
Views: 2554

Re: Displaying Gear from ECU

Try to send the gear channel info to one of the "aux" variables (ignore the R-T label for that channel).
by Bikey
Thu May 05, 2016 4:30 pm
Forum: General support questions
Topic: Displaying Gear from ECU
Replies: 4
Views: 2554

Re: Displaying Gear from ECU

are you sending a CAN stream or serial stream to the Dash 4? If CAN, then yes, no issues. If serial, you will need to feed a DL1 with the info, buy a CAN license (which I assume you have, if you are getting other channels from the ECU), and then setup gear channel in the CAN config and in the variab...
by Bikey
Tue Mar 29, 2016 7:26 pm
Forum: Sensor-related questions
Topic: How to set up additional Sensors connected to analouge inputs?
Replies: 1
Views: 1767

Re: How to set up additional Sensors connected to analouge inputs?

What did you set for your channel mins and maxs?
by Bikey
Tue Mar 08, 2016 12:40 am
Forum: General support questions
Topic: DL1 PWM Output/PWM fuel controller equation
Replies: 0
Views: 9820

DL1 PWM Output/PWM fuel controller equation

Hello - I have a car with two fuel tanks (a left and a right) that will be running ethanol and gas in varying amounts and also various states of de-tune (depending on the power to weight class entered for a given event). I have one fuel pump in each tank that pumps to a surge tank, and then connecte...

Go to advanced search