Search found 433 matches
- Thu Oct 23, 2008 11:51 pm
- Forum: Sensor-related questions
- Topic: Strain Guages
- Replies: 2
- Views: 9068
- Thu Oct 09, 2008 4:25 pm
- Forum: General support questions
- Topic: Digital Video Recorder
- Replies: 24
- Views: 47312
- Wed Oct 08, 2008 4:30 pm
- Forum: General support questions
- Topic: Digital Video Recorder
- Replies: 24
- Views: 47312
- Fri Sep 26, 2008 12:35 pm
- Forum: Sensor-related questions
- Topic: VDO Sensor Data - here
- Replies: 5
- Views: 12939
- Fri Sep 26, 2008 12:16 am
- Forum: Sensor-related questions
- Topic: VDO Sensor Data - here
- Replies: 5
- Views: 12939
- Tue Sep 09, 2008 4:29 pm
- Forum: Installation questions
- Topic: remote GPS lock indication
- Replies: 11
- Views: 21737
- Thu Aug 07, 2008 1:26 am
- Forum: Sensor-related questions
- Topic: VDO Sensor Data - here
- Replies: 5
- Views: 12939
I just did some calibration work on some more VDO temp senders. The equation on the 120* is pretty good, not so much on the 200* one. It is a 400*F sensor and I can only get to 210*F boiling water. Assuming they behave the same, an exponential equation is best. 120*C Ohm = 1850.5e-0.0183(TempF) Temp...
- Tue Jun 17, 2008 6:48 pm
- Forum: Installation questions
- Topic: RPM pickup on BMW E36 M3
- Replies: 1
- Views: 7934
You can pick up the tacho in a number of places: Connector X16, pin 20, it's the 26 pin white connector on the back of the instrument cluster, the black wire. D100 Data link Connector in the engine bay, pin 1, black wire Or any place between. (this information comes from the MCoupe wiring diagrams. ...
- Mon Jun 16, 2008 7:54 pm
- Forum: General support questions
- Topic: Dash2 battery voltage display from DL1 MK2
- Replies: 10
- Views: 16242
- Mon Jun 16, 2008 4:38 pm
- Forum: Installation questions
- Topic: DL1 firmware
- Replies: 43
- Views: 324232
- Mon Jun 16, 2008 4:30 pm
- Forum: General support questions
- Topic: Dash2 battery voltage display from DL1 MK2
- Replies: 10
- Views: 16242
- Thu May 22, 2008 9:45 am
- Forum: Sensor-related questions
- Topic: VDO temp Gauge/sensor + Pull Down to DL1
- Replies: 2
- Views: 8026
BTW, I found a nice calculator for pull-up/down resistor networks.:
http://www.electronics2000.co.uk/calc/calcdiv.php
http://www.electronics2000.co.uk/calc/calcdiv.php
- Thu May 01, 2008 2:00 am
- Forum: Sensor-related questions
- Topic: VDO temp Gauge/sensor + Pull Down to DL1
- Replies: 2
- Views: 8026
VDO temp Gauge/sensor + Pull Down to DL1
I am installing a DL1 and would like to use the VDO temp sensors with a pull down to the DL1 - the trick is I'd also like to use the same sensor to run the VDO Temp gauge.
Wondering if there are any issues with tapping off the sensor wire to the gauge for the pull downs to the DL1?
Wondering if there are any issues with tapping off the sensor wire to the gauge for the pull downs to the DL1?