Search found 41 matches
- Mon Jun 15, 2015 1:54 pm
- Forum: Installation questions
- Topic: Button common/ground
- Replies: 1
- Views: 12231
Button common/ground
I understand that the switch lines need to be grounded when that button is pushed, but to what ground? I note that there is a specific common/ground for the switches, but electrically that does seem to be the same as the D2P's main ground, so is the switch ground required? Could the buttons just con...
- Mon Jun 15, 2015 7:38 am
- Forum: General support questions
- Topic: Variables
- Replies: 1
- Views: 5974
Variables
Is it possible to define ones own boolean variable that would be set when the engine is running, i.e. 0 when RPM < 500 and 1 when RPM >= 500 and then use that variable in controlling more than one output driver? I could control each output driver I need with the actual RPM check as well as any other...
- Sat Jun 13, 2015 11:44 am
- Forum: General support questions
- Topic: Output Driver states
- Replies: 0
- Views: 36376
Output Driver states
Would it be possible to have an output driver control 3 states, e.g. Off - LO - HI? I want to control something based on ambient air temperature, but the device has 2 states (apart from OFF), LO and HI. Could I somehow use one output driver to turn it on and also to switch its states depending on te...
- Sat Jun 13, 2015 7:59 am
- Forum: Sensor-related questions
- Topic: Low fuel level sensor (reserve)
- Replies: 2
- Views: 21192
Low fuel level sensor (reserve)
Motorcyclists will be familiar with having a light come on when fuel level gets low. On the bike to which I am fitting the D2P there is a single line from the OEM dash to the sensor which also has a ground connection. The bike version of the D2P I think uses the fog light connection for this, but wi...
- Thu May 28, 2015 4:52 pm
- Forum: Sensor-related questions
- Topic: MagnetoResistive Active Wheel Speed Sensor
- Replies: 3
- Views: 23699
This is what Motec have to say on this type of sensor, you may some of info helpful in your quest m Thanks, yes I had seen that, but ultimately didn't think it helped me with circuit design for a suitable amplifier. Rather it was explaining how to allow the Motec Dash to directly read the WSS signa...
- Thu May 28, 2015 8:20 am
- Forum: Sensor-related questions
- Topic: MagnetoResistive Active Wheel Speed Sensor
- Replies: 3
- Views: 23699
MagnetoResistive Active Wheel Speed Sensor
I am fitting the Dash 2 Pro to a motorcycle from which the ABS has been removed. Mechanically this is not a problem, but the front and rear WSS were each connected to the ABS ECU which then passed a speed signal for each to the main ECU to use the data for the Traction Control function. I don't part...
- Mon May 04, 2015 10:40 am
- Forum: General software support
- Topic: Two external control questions
- Replies: 1
- Views: 5445
- Mon May 04, 2015 9:30 am
- Forum: General software support
- Topic: Two external control questions
- Replies: 1
- Views: 5445
Two external control questions
Still trying to gain a better overall understanding of what I can do with my Dash 2 Pro and so looking for advice. I will be reading the external/ambient air temperature for display and want to trigger one of the outputs below a specified temp. I believe this is possible. But can I then easily 'adju...
- Thu Apr 30, 2015 2:42 pm
- Forum: General support questions
- Topic: Dash2Pro screens
- Replies: 5
- Views: 11143
- Thu Apr 30, 2015 7:51 am
- Forum: General support questions
- Topic: Dash2Pro screens
- Replies: 5
- Views: 11143
Re: Dash2Pro screens
what happens when you press the 'Next' button and are already on screen 5? Cycles to screen 1. And "Previous" button on screen 1 will cycle to screen 5. Thanks for that. That's good, although somewhat surprising news. What about the total number of screens? Is it 5 per config set? Don't g...
- Wed Apr 29, 2015 6:25 pm
- Forum: General support questions
- Topic: Dash2Pro screens
- Replies: 5
- Views: 11143
Dash2Pro screens
I am apparently able to set up 5 different screen layouts and switch between them. Hoping someone could clarify a couple of things:- I can set up buttons to scroll between these different screens, but what happens when you press the 'Next' button and are already on screen 5? Does it simply stick at ...