Hi
We can provide an interface for some EFI ECUs. A full list of ECU makes and models that we can supply the interface for can be found here:
https://www.race-technology.com/gb/raci ... interfaces
Support (AH)
Search found 263 matches
- Wed Nov 28, 2018 9:10 am
- Forum: General support questions
- Topic: Logging ECU data (ECU adapters)
- Replies: 12
- Views: 103971
- Mon Nov 19, 2018 11:04 am
- Forum: General support questions
- Topic: DL1 not logging RPM or Analogs
- Replies: 2
- Views: 8665
Re: DL1 not logging RPM or Analogs
That sounds like one of the power loggers which we sell for race series. These don't have any external inputs as they are used for power measurement only, so just accelerometers and GPS. It would be possible to upgrade it to standard DL1 spec but it would have to come back here to be done. Please co...
- Fri Nov 16, 2018 3:28 pm
- Forum: Sensor-related questions
- Topic: Power Source
- Replies: 5
- Views: 39356
Re: Power Source
The wheel speed sensor connects to 12v, the others all connect to 5v.
Martin
Martin
- Fri Nov 16, 2018 9:50 am
- Forum: Sensor-related questions
- Topic: Power Source
- Replies: 5
- Views: 39356
Re: Power Source
Which sensors specifically?
- Thu Nov 15, 2018 9:32 am
- Forum: Installation questions
- Topic: Dash2 and DL1 MK2 Accel thruster ecu
- Replies: 1
- Views: 33568
Re: Dash2 and DL1 MK2 Accel thruster ecu
For the full list of ECU models we can provide an interface for, please see below webpage:
https://www.race-technology.com/gb/raci ... interfaces
Kind regards,
Support (AH)
https://www.race-technology.com/gb/raci ... interfaces
Kind regards,
Support (AH)
- Tue Nov 13, 2018 9:28 am
- Forum: Sensor-related questions
- Topic: Another fuel gauge set up question
- Replies: 9
- Views: 51287
Re: Another fuel gauge set up question
Yes it will give a better range with a higher voltage, but you will also be putting more power through both the sender unit in the tank and the resistor you are using.
- Tue Nov 06, 2018 2:14 pm
- Forum: Sensor-related questions
- Topic: Another fuel gauge set up question
- Replies: 9
- Views: 51287
Re: Another fuel gauge set up question
That means that the Stack gauge has the resistor built in. If you are removing the Stack gauge you will need to add one externally. You will have to remove that before you do the calibration.
Disconnect Stack gauge
Add in resistor
Do calibration.
Martin
Disconnect Stack gauge
Add in resistor
Do calibration.
Martin
- Tue Nov 06, 2018 9:26 am
- Forum: Sensor-related questions
- Topic: Another fuel gauge set up question
- Replies: 9
- Views: 51287
Re: Another fuel gauge set up question
If the system was working previously with whatever resistor was fitted then I would just stay with that and set up the DASH2 PRO for whatever voltages are provided by the system to the existing gauge.
Martin
Martin
- Mon Nov 05, 2018 3:25 pm
- Forum: Sensor-related questions
- Topic: Another fuel gauge set up question
- Replies: 9
- Views: 51287
Re: Another fuel gauge set up question
Check out the wiring diagram for a 1 or 2 wire sensor here: https://www.race-technology.com/wiki/index.php/HowDoI/DL1MK3Connect12WireSensor If you have additional resistors added in it WILL affect the values. If the float is connected to an existing gauge then you should be able to just tap in to th...
- Mon Nov 05, 2018 2:54 pm
- Forum: Installation questions
- Topic: Video4 not horizontal adjusted
- Replies: 1
- Views: 29659
Re: Video4 not horizontal adjusted
Hi
Sorry, the cameras do not have this.
Kind regards,
Support (AH)
Sorry, the cameras do not have this.
Kind regards,
Support (AH)
- Mon Nov 05, 2018 2:52 pm
- Forum: General support questions
- Topic: DASH4PRO Connector Type
- Replies: 1
- Views: 8158
Re: DASH4PRO Connector Type
Hi
It’s a Binder connector, series 720
Kind regards,
Support (AH)
It’s a Binder connector, series 720
Kind regards,
Support (AH)
- Thu Oct 25, 2018 3:08 pm
- Forum: General software support
- Topic: UPLOAD GOOGLE EARTH TRACKMAP -- OFFLINE
- Replies: 1
- Views: 11712
Re: UPLOAD GOOGLE EARTH TRACKMAP -- OFFLINE
Hi
I'm afraid that this is not something that is currently possible.
I'm afraid that this is not something that is currently possible.
- Wed Oct 24, 2018 12:55 pm
- Forum: General support questions
- Topic: Import CSV?
- Replies: 6
- Views: 13698
Re: Import CSV?
Sorry, it is not something that is possible at this time.
- Mon Oct 22, 2018 3:52 pm
- Forum: General support questions
- Topic: CAN for Haltech Elite 1500
- Replies: 2
- Views: 11374
Re: CAN for Haltech Elite 1500
Hi
We can provide a CAN interface for the Haltech Elite 1500 ECU.
If you have a DL1 CLUB or DL1 PRO, we can provide a CAN licence.
We can provide a CAN interface for the Haltech Elite 1500 ECU.
If you have a DL1 CLUB or DL1 PRO, we can provide a CAN licence.
- Tue Sep 11, 2018 8:49 am
- Forum: General support questions
- Topic: Need to update settings on Dash2 v9.3.4
- Replies: 7
- Views: 11994
Re: Need to update settings on Dash2 v9.3.4
You can't read the configuration back from the older firmware, it was a one way process. That is one of the big improvements in the new firmware.
Martin
Martin